Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
Our prototype is back. At first, I used NRF Connect to flash it, but the official PC software couldn't flash the firmware. I followed the wiring instructions: (1) connect...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi
I used the SDK14 with nRF52832, and carry out the blinky example. When using the Android, the BLE device could be found, but the IOS cannot scan the device. So could...
Hi,
So I am working on NRF52832 with S132 6.1.0 and SDK 15.2.0 mtu and data lenght testings. During that time I was unable to change mtu multiple times while connected ...
I have a ble device and want to write a byte array in nRF Master Control Panel. Firstly, it can be written. But i don't know ho w to input it. My byte array is [-128, -64...
Hi,
I looked at this comment.
If this function (sd_power_system_off) is executed, can I wake up the device again with a soft reset?
If not,
What is a function that...
Hi,
In the documentation nFR523832_PS_v1.4, on page 107, the registers HFCLKSTAT and LFCLKSTAT when in reset mode, indicates that the LFCLK is not runing, and neither the...
Hi Everyone
I am trying to use 2 instances of SPI SPI0 AND SPI2 for Epaper Display and MCP2515 CAN bus module respectively.
Epaper and CAN are working fine if one of them...
I am using NRF52 SDK version 15.3. I am using the app_usbd_cdc_acm module to create a virtual serial port between an NRF52840 DK and a Linux laptop. I am sending messages...
I'm looking into migrating my project from gcc/make to Segger Embedded Studio, because I have some tricky debugging to do and SES should be a bit easier to use than GDB for...
Hi all,
I use nRF52832-QFAA, S132 2.0.0, SDK 11.0.0, IAR 7.5, Windows
Upon connection, I am trying to resolve the peer "random private resolvable" address (not for whitelisting...
I have been having issues of when I operate some components in the system the nRF52832 goes into a hard reset. I have seemed to fix a lot of the hardware issues but there...
NRF_LOG_INIT HardFault in balloc (see stack trace below).
Code works perfectly without bootloader. However, when the bootloader is present it seems to already have initialized...
I followed some code I found for setting device name. Right now it just transmits as N/A for the device name. Any help would be appreciated.
Here is my code:
/** * Copyright...
Hello,
I am new to Nordic and started using nRF52832. We started a new project. It requires
Act as Peripheral (Single role) only.
Only Advertisement for 3 minutes...
I find the combination of both EasyDMA and non-EasyDMA, plus nrfx and legacy driver in SDK 15.3.0 quite confusing. Where is the implementation of the legacy SPIM (EasyDMA...