Hi,
1. How to set read protection and how to verify read protection for nRF54LM20B? 2. The test DK is PCA10184 0.7.0. 3. My test is as follows: Read protection will never...
Hi There,
I am currently developing an LTE-M application on nrf9151 using ncs v3.2.1, the device is a MQTT client that publishes telemetry periodically every 3 minutes,...
Hello Nordic Team,
I am working on an nRF52833 project using nRF5 SDK 17.1.0 with Secure DFU Bootloader.
Environment:
MCU: nRF52833
SDK: nRF5 SDK 17.1.0
SoftDevice...
i2c_write_read() returns -5 (EIO) immediately when writing register 0x01 to the sensor. Logic analyzer confirms the sensor clock-stretches SCL for ~14µs+ after receiving the...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
log.zip
I use custom board for nRF52832
I connected it with JLink, and installed SD132 with nRFgo Studio (successfully)
after then, I cannot connect to chip
...
hi guy . I m triyng to understand if could be possible to send a at least 300 hz input signal beetwen two boards nrf52840 with the trasmission protocol ANT.
I tried to use...
Hi!
1. We are using 1 Client over Serial and 30+ Server nodes over mesh network
When you want to know FW info regarding Client, you can call serial command like Opcode...
Hi, I'm working on project using nRF52840-DK board with nRF5_SDK_15.2.0_9412b96. The program collects data from two UARTs, process data and sends results to Android over BLE...
Hi Everyone,
I am using BL651(NRF52810) chipset.
NRF_P0->DIRSET |= (Reg_MOTOR_ILERI | Reg_MOTOR_GERI); NRF_P0->DIRSET |= (Reg_SUTUN_1 | Reg_SUTUN_2 | Reg_SUTUN_3); NRF_P0...
Hi,
I am looking for the process of flashing the NRF52840 with the BLE SoftDevice (S140), a bootloader with uses the BLE link for DFU and my general application code.
...
Hi,
i get hardfault for some reason. This is RTT output:
and this is the output of GDB:
and backtrace gives this:
is there a nice way to find out where the hardfault...
Hi, does the nRF9160's LTE modem support waking-up the application processor using an incoming call?
The OPS indicates that a DETECT signal can be input to a GPIO pin for...
Using nRF5_SDK_15.3.0, soft device 132 (Rigado BMD-300 eval kit), segger embedded studio
I'm trying to control ADS1231 by listening for DRDY to go low and pulse an output...
Dear nordic,
I have some doubts regarding this both examples. I am new in this thread coap
1. In Thread coap cloud client example uses coap post method is it right?(i...
Hi! I am evaluating Extended Advertising. Is it possible to get the rssi of ADV_EXT_IND at the BLE_GAP_EVT_ADV_REPORT event? That was possible with AUX_ADV_IND. My environment...
in advertising_init(); function, i add some code like below:
#define def_uuids_complete 1 //#define def_uuids_available 1 #define add_vbat_service 1
/**@brief Function...
Hi everyone,
I'm currently trying to develop an application with the mesh, the uart and the DFU.
I've started the project with the sdk_coexistence for use the uart and...
Hello
I am using a proprietary board containing NRF52832 chip
using Rigado board I can flash the system on Rigado board perfectlly
using my costume board, by using...
When my app starts up, I call "lte_lc_init_and_connect()" by using the Zephyr system workqueue. With it running on a separate thread, my main thread is still blocked. I have...
