Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
I have three buttons connected to pins PO.07, PO.08, PO.09 on my card. I changed the pin assignment and for the first two I have no problem using them as buttons, but I can...
Hi there,
I've been trying to figure this one out for a day or so now with no luck.
I'm successfully able to build and program using Segger Embedded Studio, but I would...
Hi
I am new to nrf52840. I am trying to communicate on I2C bus with Cypress semiconductor CY8CMBR3116 capacitive touch IC. Some how I am able to connect the on I2C bus...
Hello,
I'm developing a custom application based on SDK 15.2 on nRF52 using softdevice S132 v6.1.
In my development, I want to ensure timestamp synchronization between...
Hi,
I am using NRF52 SDK 15.3 on nrf52840 Preview DK
I am using BLE to transmit data, I want to use PPI to get readings off of SAADC but using 'app timer' instead of TIMER...
I'm currently on a question for which the documentation here can't help me.
If I'm correct, the Dual-Bank Update allows to retain a safe copy of the old firmware image...
Hi,
I am using esb project of SDK15.3 to test esb PTX and PRX function.
The default setting of address-0 and address-1 is 0xE7E7E7E7 and 0xC2C2C2C2, and PTX and PRX can...
Hi,
1.I want to develop the my product using nrf51822 with PCB antenna(as shape given in sdk hardware) with following board stackup-
2. i am going to use cap-0603 in...
Hi,
I am using nrf52840 S140 PCA10056 SDK 15.2.0 version with example ble_app_multirole_lesc_S140_PCA10056 . i am using Segger Embedded studio IDE. So now problemis i am...
Hi,
I am trying to get my systemOFF current below 1uA, but Im struggeling.
normally I use MBED, but to eliminate that variable, I just did a test without MBED, I took...
Hello together, I am experiencing problems with the nrf52840. I got the BLE_APP_Blinky example to run. Now I am trying to get the BLE_THROUGHPUT example experiment to run...
Dear nordic,
I want to know something regarding your SDK. I have nrf52832 development board and i use sdk 15.2 .
1. if i want to use BLE 4.2 version what changes i want...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I added the UART example to...
Hi,
I am working on a project where my mobile phone will be acting as a central device and nRF52840 DK will be acting as a peripheral device. I used the nRF UART and nRF...
Dear nordic,
I need more information regarding this?
1. I heard the BLE one packet has possible 20 bytes. but i tested this example and connect using nRF connect app...
