We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
log.zip
I use custom board for nRF52832
I connected it with JLink, and installed SD132 with nRFgo Studio (successfully)
after then, I cannot connect to chip
...
hi guy . I m triyng to understand if could be possible to send a at least 300 hz input signal beetwen two boards nrf52840 with the trasmission protocol ANT.
I tried to use...
Hi!
1. We are using 1 Client over Serial and 30+ Server nodes over mesh network
When you want to know FW info regarding Client, you can call serial command like Opcode...
Hi, I'm working on project using nRF52840-DK board with nRF5_SDK_15.2.0_9412b96. The program collects data from two UARTs, process data and sends results to Android over BLE...
Hi Everyone,
I am using BL651(NRF52810) chipset.
NRF_P0->DIRSET |= (Reg_MOTOR_ILERI | Reg_MOTOR_GERI); NRF_P0->DIRSET |= (Reg_SUTUN_1 | Reg_SUTUN_2 | Reg_SUTUN_3); NRF_P0...
Hi,
I am looking for the process of flashing the NRF52840 with the BLE SoftDevice (S140), a bootloader with uses the BLE link for DFU and my general application code.
...
Hi,
i get hardfault for some reason. This is RTT output:
and this is the output of GDB:
and backtrace gives this:
is there a nice way to find out where the hardfault...
Hi, does the nRF9160's LTE modem support waking-up the application processor using an incoming call?
The OPS indicates that a DETECT signal can be input to a GPIO pin for...
Using nRF5_SDK_15.3.0, soft device 132 (Rigado BMD-300 eval kit), segger embedded studio
I'm trying to control ADS1231 by listening for DRDY to go low and pulse an output...
Dear nordic,
I have some doubts regarding this both examples. I am new in this thread coap
1. In Thread coap cloud client example uses coap post method is it right?(i...
Hi! I am evaluating Extended Advertising. Is it possible to get the rssi of ADV_EXT_IND at the BLE_GAP_EVT_ADV_REPORT event? That was possible with AUX_ADV_IND. My environment...
in advertising_init(); function, i add some code like below:
#define def_uuids_complete 1 //#define def_uuids_available 1 #define add_vbat_service 1
/**@brief Function...
Hi everyone,
I'm currently trying to develop an application with the mesh, the uart and the DFU.
I've started the project with the sdk_coexistence for use the uart and...
Hello
I am using a proprietary board containing NRF52832 chip
using Rigado board I can flash the system on Rigado board perfectlly
using my costume board, by using...
When my app starts up, I call "lte_lc_init_and_connect()" by using the Zephyr system workqueue. With it running on a separate thread, my main thread is still blocked. I have...
