We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
I am using a custom NRF52832 board. I am using Nordic SDK + BLE code, and whenever I am trying to do an erase of flash memory with start address as 0x70000 and end address...
I try to get the info listed in the following paragraph (From the nRF91_DK user guide) but just get run the run around with the web site. Anyone got a link to this information...
The flash requirements for both the S132 v5.0.0 and v5.1.0 are the same, however the size of the v5.1.0 softdevice is quite a bit smaller.
S132 v5.0.0 uses flash addresses...
Hello I try to get the mac address of connected device
/**@brief Function for the application's SoftDevice event handler.
*
* @param[in] p_ble_evt SoftDevice event...
Issue with Zephyr software platform and sleep state for the Nordic chipset. We can see when using the power management sample code for Zephyr that it consume 300 uA in sleep...
hi,...... i am merging the nRF52832 and heart rate sensor BH1790, SEGGER 15.2V i want to read the heart rate sensor , for that i want to write the paramater of address, 41h...
After beating my head against the toolchain for quite a while, I finally managed to get SES to compile the ble_app_uart for the nRF51822 using the s130 soft device. It works...
nRF52832(PCA10040) plays role of central(ble_app_multilink_central) and
HM-10(TI 254x) runs as spp peripheral.
nRF52(with SDK15) receive adertizement packet but loss...
We are using device nrf52840 with sdk 15.0.0
The problem is: High current consumption, typically around 2 mA. But over time drifts up to 9 mA in a period of 12 hrs.
...
Hi, first post here...
I've been using Nordic in the form of Laird modules and SmartBasic to get my application up & running. Now I want to migrate to using the nRF devices...
Hello,
I am trying to use nrf-mpu-examples in eclipse from this link github.com/.../nrf5-mpu-examples . I have provided all required libraries and header files but I am...
I am developing a device that will receive over the network lte a video signal in real time and display it on a screen with a resolution of 13-15 inches. Based on the chip...
I´m trying to build an application similar to the peripheral side of the app_mtu_throughput example. I need to send a large buffer via notifications to the server.
I'm using...
I am using NRF-52832 on a custom hardware. It works well on Android but on IOS (e.g. iPhone 7) it disconnects after 30 seconds.
After analysing with the sniffer, its observed...
Hi,
I had change NRF_ESB_MAX_PAYLOAD_LENGTH to 250 and modify payload_length of NRF_ESB_DEFAULT_CONFIG to 250.
Why I can only send 8 byte packet out by using "nrf_esb_write_payload...
