We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I am testing my I2C function by using ".examples\peripheral\twi_sensor" of SDK 15.2.
Because my SDA and SCL is define in P0.04 and P0.02, and my I2C Slave is MPU6050...
Hello,
I would like to know that what are the provisioning parameters needed to add an Unprovisioned device into a mesh network?
Thanks and regards,
Jahnvi.
We, I am using nRF 5 SDK v 14.2.0.
This time, without using WDT, using only the application timer, We are developing a process to send data by detecting acceleration and...
Hi,
I'm currently trying to implement Peer Manager in my existing project, for both pairing and bonding. I'm using the ble_app_template in examples/ble_peripheral in the...
Is it possible to use the TWIM and TWIS at the same time with 2 different I2C buses with openthread.
I tried this with THREAD SDK 1.1 and had link problems because of the...
Hi, I'm trying to setup attribute reporting on zigbee HA, the device role is ZB_ZCL_CLUSTER_SERVER_ROLE, I want to configure reporting for cluster 0x0006, so each time I flip...
SDK v14.0, SD132 v5.0.0
We're creating and starting app_timer instances before we enable SoftDevice via nrf_sdh_enable_request(). It seems to work, but I remember that...
Hello,
Is Bluetooth 5, capable to communicate with BLE devices as well as classical BT devices? I think this dual capability is called smart ready.
We are planning to...
Hi,
I can program our old Nrf24LE1 boards with Nrfgo Studio, but when I tried using Nrfgocli command it fails to connect to
the board. My motherboard is set to number...
I noticed that CMSIS Configuration wizard expects values in HEX and converts them into decimal in the sdk_config.h file.
e.g. for SEGGER_RTT_CONFIG_BUFFER_SIZE_UP. I entered...
Hello there, I am using nrf52840 The mark is: N52840 QIAAC0, SDK: nRF5_SDK_15.0.0_a53641a, SD: nRF5_SDK_15.0.0_a53641a, I used the BLE ANCS routine and encountered this problem...
Hello,
We have a custom board based on nRF52832. The problem is that when trying to run basic example Blinky (examples\ble_peripheral\ble_app_blinky\pca10040\s132\arm5_no_packs...
Timer interrupt does not work well. In the code below, LED doesn't turn off and "interrupt!" message is not received. I really appreciate it if you give me any advice.
Hi Everyone,
I want to make a program code to establish the connection between MCU(nrf52832 chip) and accelerometer.
What are the conditions required? and i need some...
