We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
I'm using nRF52840 with SDK 15.2, and SD backend for Flash storage. I try to implement a verifiedWrite() method to write to flash. And it work most of the time, but fail sometimes...
Hi,
Is it possible to find comparison on the power consumption when running the internal DC/DC converter at 1.8V and 3.3V?
I have an external SD-card that needs a lot...
In the documentation for the s140_nrf52_6.0.0 I find the following statement: "The PPI channels and groups that are reserved by the SoftDevice when enabled are defined in...
MCU: nrf52840
SDK: V 15.2.0 porting with nRF-IEEE-802.15.4-radio-driver
problem:
ble_nus_data_send function sometimes returns BLE_ERROR_GATTS_SYS_ATTR_MISSING error...
Hi,
I am currently updating a firmware from SDK 12.1 to SDK 15.3 on a custom board using a nRF52832. Application itself has been upgraded and works well with Soft Device...
In the use nRF5_SDK_15.2.0_9412b96\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay，PCA10040. 1.Remove keys and leds from BSP。 2.Delete analog HRS timer...
hi all:
My project need 4 devices communicat with 1 host ,all use nrf51822 chip,is it possible？Now i have a problem ,when the third device communicate with the host ,will...
I have been doing some testing around DFU and I have noticed something strange.
My application size (according to nRF Connect memory read) is about 78 kB. (Left Image...
Hello,everyone,
I have successfully installed nrfutil using pip install nrfutil, but when I type nrfutil in the terminal, it shows -bash: nrfutil: command not found, how...
Hi,
We were trying out the long range central and peripheral examples found in github with the nRF52840 DK boards but we are not getting the specified range(We did switch...
Hi everyone, I have nRF52840 DK and I want to write an application program that uses multiple wireless communication protocols (e.g BLE , Zigbee , Thread) and can communicate...
Hi,
I am trying to add Nordic UART service(NUS) in ble_app_relay_rscs, but after adding nus service in application device is not advertising and there is no print in serial...
Hi! I am trying to read the voltage of a LiPo battery as explained in this blog post. The code on github however, is not compatible with the latest SDK for the SOC (12.3)...
Hey guys,
we are currently evaluating the pc-ble-driver-js. We want to get it running on a Raspberry Pi 3.
The Nordic nRF52840 module was flashed with SD Version 6.1.0...
