Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
HI.
I am following the document http://infocenter.nordicsemi.com/pdf/nRFConnect_BLE_User_Guide_v2.2.pdf to work with nRFConnect desktop App and my DK BMD300(Rigado). ...
Hello,
I'm trying to play voice using PWM in nRF51822.
I've already experienced this using other MCU before.
So. I'm trying.
Voice source data is 8bit / 8K / mono...
Hi,
I am working on nrf52832 , SDK15 and softdevice S132. I am modifying the ble_app_hrs example code in SDK
I was trying to implement a whitelist with the address of...
I am using ble_app_uart SDK_11 s130 on nRF51-dk. I would like to make the device running on ble_app_uart connectable but not discoverable. The Android app will have pre-knowledge...
I am using nRF52840 with sdk 15.0 version. I am able to read OR write data into flash using fds library. But now i want to write one or two bytes into flash and read this...
Development Kit - nrf52
SDK Version - 15.0.0
IDE - Segger Embedded Studio
Computer Platform - Windows 7 - 64 Bit
Setup : I am trying to interface an E Paper Display...
I am trying to detect when mtu has been successfully negotiated through the ble_evt_handler function, which is passed into NRF_SDH_BLE_OBSERVER as shown below:
// Register...
Hi - I'm trying to program the Thingy52 using my nRF52840 DK and Macbook Pro. I've got the Thingy connected to the DK via the 10-pin cable. The first time I ran nrfjprog on...
Hi there!
I have migrated ble_mpu_simple from sdk14.2 to sdk 15.2.
I use Keil uVision to test "nRF5_SDK_15.2.0_9412b96\examples\nRF5-mpu-examples-master\nrf5_ble_mpu_simple...
Hello,
Let me start off by saying that in our use case we are transferring large amounts of data (megabytes) through BLE. This works fine on iPhone 6s+, iPhone SE, iPhone...
Hi,
We're looking for a Bluetooth chipset / module for a Android Pad hardware.
Given that Android 8.0 BlueDroid stack requires Bluetooth chip support HCI commands, is...
Dear all we are using nrf52810(48pin).we did not find exact solution about how many i2c and spi available for that.in which pin we have to connect i2c device and SPI devices...
Good day!
How can I calculate the maximum throughput for BLE Mesh running on the nRF52832 and the S132 without packet loss in ideal conditions?
I have tested throughput...
