Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi,
Starting a new design with nRF52832 that requires TWI, SPIM, and UART interfaces. Also need a wake on GPIO for the power button. Is there a preferred pin assignment...
Hello, we are experimenting with proprietary RF transmissinon between two nRF52832 devices. We are currently trying out the esb_ptx and esb_prx examples, toggling GPIOs on...
Hi,
I'm using a nrf52810 on with SDK V15.2 with SD112.
The application uses the app timer and also TIMER1 for other purposes (and TIMER0 is locked by Softdevice).
What...
Hello,
We are considering bluetooth module of laird tech for our ongoing project, it has Nrf52810 chip. Please verify the below things Schematic: 1) this module has onboard...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am now trying to write to the SD card at 1000 Hz (1 ms) by combining "fatfs example" and "app timer...
Two nRF52810 devices, one is PTX and another is PRX, use the ESB protocol.
This project is very demanding for the timeliness of data transmission, in order to improve the...
It would be very nice if the SoftDevice API Documentation at https://www.nordicsemi.com/DocLib included PDF downloads for each SD version as well as the current online HTML...
Hello Nordic community,
I'm wondering about how those BLE trackers (i.e. Tile , Trackr) work. Specifically, what kind of advertisement strategy makes sense for these types...
Hi
I am developing RX device to connect with Smart Remote 3.
The RX device system is Linux embedded. I need to run OTA function in Linux embedded to update SR3 F/W.
...
Hi,
I am using STM32F030C6 MCU with Laird BL651 module.
Keil-IDE v5, windows 7(64-bit) system configuration.
I need to get the sample code for the application development...
Hello, I have following problem.
My DK is not recognized by J-Link / nRFgo Studio.
I tried to reflash J-Link by pressing BOOT/RESET and then drag and drop J-Link OB...
Hi,
I would like to update the Device Information Service's (DIS) serial number characteristic to reflect the actual serial number assigned by our production equipment....
Hi, I am using the following setup: Wireshark 2.6.5 (updated yesterday) Sniffer 2.0.0-beta-3 (nrfsniffer200beta312oct20181c2a221.zip) nRF52840-DK (used by the sniffer) nRF52840...
I have a custom board that uses Nordic NRF52832 as MCU. For laying out crystals, BLE part and decoupling capacitors, I used reference layout from documentation.
32 MHz crystal...
