Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi,
I am using nRF_SDK_15.0.0_a53641 and writing a program with keil.
I am receiving data from the sensor with TWI communication and writing it to the sensor by SPI communication...
Hi everyone,
Device : nRF52832
SDK version : 14.2
Softdevice : S132 v5.0
I am facing a problem when changing the interrupt priority dynamically. Let me explain the...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
Hello
Previous projects used SDK11 protocol stacks with BootLoader and DFU
About the BootLoader of sdk11, DFU is different from sdk15. Please consult me. Thank you.
...
Hi Sir,
As check below link, we know how to re-write the bootloader address.
https://devzone.nordicsemi.com/f/nordic-q-a/26300/how-to-use-nrfjprog-to-write-uicr-bootloaderaddr...
Hi,
I am implementing an application where I need to transfer a 32 byte array via NFC. The only issue is that existing modules in nrf52 sdk have support for UTF-8 encoding...
Hi,
I am looking for a flasher that can be used for nrf24le which can be used in serial production. I found segger Flasher portable plus for nrf51, This device can work...
HI, team.
I use two nrf52840 PDK run the example light switch, light switch proxy server and client.
for the light witch proxy client, when press button 0 it will call...
I have an application where 2 peripherals are gathering sensor data and sending this using notifications to a central. Every connection interval, new sensor data is available...
Is it possible to scan for eddystone beacon advertising packets using a nRF52 central device?
I'm trying to accomplish having authorized beacons such as waypoints that...
Hello,
I am developing a bootloader on nRF24LE1. The NUPP configuration is: the first 24 pages (page 0 - 23) are set to be unprotected and the last 8 pages (bootloader)...
I have three nRF52840 DK. I'm trying to make some project on Bluetooth Mesh network using nRF52840. And how can i make the use of mobile as node in network along with 3 nRF52840...
Good day!
In my BLE project I use connection parameters negotiation module. In order to ensure software consistency there is a test for memory leakage. After some investigations...
Software:nRF5_SDK_15.2.0_9412b96
HW: PCA10056
Modify:
1. Added LED blinky and PWM on the blink FreeRTOS sample.
2. Added task 2 demo2 as dummy to test the freeRTOS...
