My customer is now unable to disable secure erasure after using the APPROTECT function. Is this correct?
Please let me know if there is another way to check this.
”nrfjprog...
Hi. I have an idea for a product and I'm looking into different platforms to start prototyping. Something nrf9160 based looks like the way to go, and it would be a huge advantage...
After full update modem firmware and reboot, i got this error:
E: Modem library init error: -116, lte_lc not initialized
The only way to work around is power cycle.Po...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
Hello, Super quick but important question, are the SMD footprints in the nRF52840 reference circuitry recommended BOM (ie image attached) in imperial or metric units? and...
Hello,
The subject of this post is mostly accurate in that I am developing custom hardware that is based on the nRF7002DK. For all intents and purposes, the Interface MCU...
I'm just getting started with the Nordic chips so I will apologise now if I have failed to find my own answer amongst all the devzone content.
I want to use the NUS service...
Dear all,
I have a problem with secure connection between Android (nRF Connect) and my custom board with nRF52832. I'm usind SDK 14.2 and SD_132 v.5.0. I'm using secure...
Hi All,
Anyone know the aggregator example can run on the nrf52 PCA10040 DK?
https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role I fail to compile the...
I've got a bit of an issue with turning off specific debug statements. If I try and adjust the log level, I get a run time failure. If I try and comment out the specific debug...
I have changed the RAM (rwx) : ORIGIN = 0x20001fe8, LENGTH = 0x2018 in ble_app_buttonless_gcc_nrf51.ld. Build, it appears to me /usr/local/gcc-arm-none-eabi-4_9-2015q3/bin...
Hi to all,
i have an example that it implemented a device with some charactristics, when i use sniffer to sniff these packets i can not see the packets data because the...
I am experimenting with the mesh light-switch example. I want to control two LEDs on a single node using the SimpleOnOff model. I know I should add a separate element and...
Hello,
please help to grasp the problem,
when using the timer to control gpio pin with constant period as shown below, if trying to do advertising for BLE communication...
I am trying to understand light_switch_provisioner application. I am using Segger Embedded Studio for debugging. I have inserted a breakpoint at line number 631 in node_setup...
Hi
We are currently doing RF certifications on a product using a nRF52840. Japanese radio law has the power stabilization requirement:
"When the input power of equipment...
Hi Experts:
I'm using SDK15.0, softdevice_v6 to Development NRF52832, which is developing a non_security bootloader. The bootloader adapted from the example program can...
Hi there,
I was wondering if someone at Nordic could verify something for me. I had a go at modifying the lightswitch example (node_setup.c) in the mesh sdk, to instead...
I've seen many posts asking this question, but with no definitive answer. I've seen latencies for various GPIOs acting as either SPI or TWI, but no baseline interrupt latency...
Has anyone modified the spi_master_using_nrf_spi_master example (or otherwise gotten) the Crystalfontz CFA211TFH 128x64 panel running w/o mods on the nRF52 DK? I have a panel...
Hello,
I captured following data using a Bluetooth dongle for WIN 7 and a Bluetooth keyboard . I also used Wireshark with USBCap driver to capture data going from BT Keyboard...
