Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi,
I followed the instructions for importing the Thing:52 firmware into SES and managed to get the firmware compiled and loading, and the code reaches the main function...
Hi,
I'm following DFU quick start guide and I'm using mesh SDK v2.0.1, I have a problem in step 4 wheere I need to generate a hex version of device page, I did this :
...
Hello,
Are there any conditions where the sd_ble_gap_disconnect() will not immediately terminate the link?
My Setup: Nrf52, SDK 13.0.0, own board, based from HRM code...
Hi!
I want to start scan in central mode after one connect has established and I received success evt PM_EVT_CONN_SEC_SUCCEEDED:
In a SDK13 I can make same, but at SDK15...
Hello!
On the firmware for a certain product, we are using the scheduler module to manage the access to the peripherals (SPI, TWI, Timer, ...), and have also enabled its...
I implemented manufacturer specific advertising to transmit important data without having to connect to the ble peripheral. These data can change over time so I need to be...
I measured the power consumption on NRF52840 DK with project peripheral blinky (SDK15.0.0). The average current is 704uA and the base current is 680uA when connecting to another...
I have a test suite connecting to a nRF52832dk using RTT. This one test writes random data to the UICR config area, resets the chip, then reads back the config.
When running...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
I am about to buy 5 pcs of nRF52840 DK Development kit for nRF52840 SoC to use for Long Range. How can I ensure the development kits are mounted with chip revision C or later...
Hi Team,
I have read in nordic documents that BLE 5.0 will have 1.4 Mbps of through put.
But when i am testing the through put example with my nrf52832 board, i am only...
Hello. I'm using the example of the light_switch_server project. I need to configure a server (light bulb) driven by 3 clients (buttons), how can I do? I tried this way, but...
Hello Nordic,
I have to transmit data from the nRF Chip(now i'm testing nRF52832 DK Board) to a PC on UART serial.
Each beacon has transmitted advertising and scanRSP...
Based on the nRF24L01P Product Specification 1.0, after 24L01+ enters into Standby-II state, the only 2 ways to leave this state are 1, set PWR_UP to 0, 2; 2, Feed data into...
