Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
I've picked up the DK after a break. Installed the toolchain on my new laptop and was ready to throw the 'blinky' example from the SDK on to it to get started. It did not...
Hi Nordic experts:
I use a device with thingy52-provision-demo firmware(from git-playground), and another device with serial-example to provision the thingy-provision-demo...
Hi.
I want to advertise switching 1Mbit PHY and CodedPHY every 5 seconds.
I designed it like this based on nrf52 ble app uart long range example.
advertising_start(coded...
Is it possible for an app after having gone to sd_power_system_off to reset by button without triggering DFU?
The app seems to need CONFIG_GPIO_AS_PINRESET to be set so...
I am working with production Rev 1 on nrf52840 DK v1.0.0 (2018.19). The spec section 6.35.10.2 Bulk and interrupt OUT transaction say
Until that transfer is finished,...
I am working on mesh application icatin nrf52832 . i want to integrate mesh and nrf sdk application , So i followed this application and mesh_app_uart example Example for...
Hi all,
I am testing DFU example in Mesh SDK . I follow this tutorial : http://infocenter.nordicsemi.com/index.jsp . But when I execute to step 4 :
I get this error...
Hello,
I am new to Nordic products so please apologize me if I am asking a trivial question, but a bit lost on it. I would like to use Thingy 52 board for my project ( I...
Hello,
I am having a trouble with my code. There is an RTC sensor Which has the address 0x32. When the sensor is connected to the TWI lines, there is no problem and it...
Hi There,
I've been developing a product using the NRF52DK. I had some custom PCB's made after I had my circuit designed, and I programmed them with the NRF52DK. Now my...
This one is weird. On a new board with a Rev C '840, when trying to reset the processor using 'nrfjprog --program nuttx.hex --sectorerase --erase', a Decawave DW1000 connected...
I want to add ANCS client to my code. Like in the ble_app_ancs_c example, I start a timer after BLE_GAP_EVT_CONNECTED. The timer handler calls pm_conn_secure() if the connection...
Hello
SDK12.3, nRF51822
I'm trying to interface the ssd1306 the program freezes in function app_twi_perform internal_transaction_cb is not called internal_transaction_in_progress...
With our nRF53832 device we are not using NFC.
For the lowest power usage should I keep them as disabled NFC pins or change them to GPIO pins and drive them to the same...
