I'm trying to test NFC on a NRF52840 Development Kit (PCA10056 - .Version 3.0.3), using NRF SDK 2.6.0.
I'm testing using the RECORD_TEXT sample project ( C:\ncs\v2.6.0\nrf...
I am working with a custom board based on nrf52833 , SDK 17.1.0 and ble_nus service implemented.
Final goal is to be able to connect to devices only if they provide the...
During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
Hello,
I am working on a project that will require external flash. Is there an example program compatible with the following external flash device?
M95P08-I - Ultra low...
Hey,
the USB connection to my nRF54L15-DK isn't working anymore.
It is not showing up in nRF Connect Desktop and I can't find it under /dev/tty... or /dev/cu...
The...
I am relatively new to embedded and am wondering if there was a "best practices" guide / checklist for production deployment somewhere. Things like making sure you are using...
Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
Hi,
I'm looking into the reliability of the BLE connection from one nrf52 to another nrf52. I'm looking to understand a few things.
Once a connection is established...
In both the SDK and production specification (PS 1.4) it is noted that the TIMER (Timer / counter) peripheral in 'COUNTER' mode (0x01) is deprecated.
For implementing a...
In my current case there is a relay node to which want to send RSSI values of beacons nearby and then relay the same information across other relay nodes in the network, So...
what is the problem of "ERROR Failed to open nrfjprog: Error occured when open device long term. Errorcode: CouldNotLoadDLL (0x3)" , when i use the nRF Connect.
the version...
Hi,
How can we receive more than 20 bytes of data from the phone? We are using s132 and SDK 12.3. I know how to send more than 20 bytes of data from the NRF52 to the phone...
I am a newbie to Nordic chips and tools and new to bluetooth. My company is doing a BLE sensor. We have a prototype board ready and I am trying to do some firmware for it...
Hi I have tried the light demo example, where I do not understand the difference between "reply_Status" and "publish_State" on the server, then someone can explain the difference...
I am currently working with an NRF51822 and managed to change the TWI frequency to 400kHz in the twi_hw_master (this worked, I can see it on the oscilloscope). I commented...
I'm trying to upload via DFU from one nRF52832 to another nRF52832
I use SDK 14.1
First I want to enable CCCD at the master side.
static uint32_t cccd_configure(uint16_t...
Dear Sirs,
We are evaluating nRF52840 now, How far is the maximum range it can reach while keeping the data rate at 2Mbps if we use two nRF52840 for point-to-point communication...
