Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
How can I disable NRFX_LOG_INFO calls in the PPI driver? I've set NRFX_PPI_CONFIG_LOG_ENABLED 0 and even NRFX_PPI_CONFIG_LOG_LEVEL 0 but that doesn't stop messages like the...
Hi,
This is Srivisakh. I am using a custom made board integrated with nrf52832 board in which UART is configured. I am using Segger IDE for code development and building...
Hello I have what I hope is a simple question regarding the Internal DC/DC on the nRF52832 and thus nRF52810. I am assuming it is the same internal design, correct between...
We are just in the very beginning of developing a mesh network with 150 devices and a gateway (with a nRF52840 in it). We want to find the best strategy for provisioning....
Hi everyone,
thanks for this discussion - this question addresses almost exactly a potential use case I've been looking into.
I'd like to try and implement something this...
This is from the documentation:
[in,out]
p_length
Pointer Length of the string. Amount of sent bytes.
I'd translate it to a pointer to the requested length...
Hello all, I already did some research finding similar questions and answers in this board, unfortunately I still do not have answer, maybe some can can help pls?
I have...
Hi,
I'm trying to test the BLE Mesh example. I want to prove that whether the feature of Relay is able to work or not. So, I use the functionality of heartbeat publishing...
I am running SDK 14.2.0 and trying to update only the bootloader. Very minor changes were made, resulting in no size increase.
I ran nrfutil (V3.4.0) using the following...
Hi, Everyone
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
I am testing the input and output of the uart using nRF5_SDK_12.3.0_d7731ad\examples\peripheral...
Hello!
I am using nrf52832 with SDK14.0 and SD 5.0.0
I have issue with Flash data storage. I am using code from example (fds_test from github)
Writting works good...
Hi,
nRF52832 uses which type of modulation technique?
Whether nRF52832 is Adatpive euipment or Non adaptive equipment . Please clarify?
Wireless module certified individually...
Hi all,
I am merging my code from Mesh 1.0 to 2.0.
I am trying to put both Provisioner and Simple On/Off Client into one board,
and then the other board is simple...
Hi,
May I ask what's the minimum reference circuitry for running nrf52810 without RF? Thanks.
Our need is as follows.
1) RF, eg, Antenna is not needed 2) GPIOTE 1 channel...
