Hello, I have used nRF Connect for Desktop with the nRF52840 dongle and it works perfectly as far as using the dongle as a central device and a peripheral device (BLE advertising...
Hello, when flashing t device using nrf connect icon, it fails to flash with following message
After investigation I found the generated_nrfutil_batch.json (autogenerated...
Vidar Berg appears to be off today. I hope he's okay. Could someone please pick up Case ID: 360532? We only get about 4 hours of overlap per day due to difference in time...
Hello,
I've been working on a feature lately that involves writing the OTP registers in UICR on nrf54L15; after writing the registers I also wrote the protected value (0x50FA50FA...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
We are using a BM833 chip on out PCB. There, we may or may not (config-dependant) interact with a sensor via I2C. We observed (statistically), that using the I2C communication...
Hi,
I’m reviewing the release notes of the Zigbee R23 add‑on , and I see that the compatibility table maps each add‑on version to a specific NCS (nRF Connect SDK) version...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
Hi all
The errata sheet V1.8 states that the errata 143 applies also for the Bluetooth Low Energy mode. Does that mean that the BLE stack of the SoftDevice S132 is also...
Hi,
I am using nRF52832 DK and other same custom board, sdk v15.0 with SES IDE. My application like this:
For ble peripheral used example ble_app_uart and for central...
Hi Sir,
In my system (windows 7), I had install the GCC 4 .9 2015 q3 for SDK 14.2.0/12.3.0.
As reference the release note of SDK 15, the GCC upgrade to 6-2017-q2-update...
Good Morning Team, Hope your day is going well! Can you please provide the Full Material Disclosure (FMD) document for below part since I could not locate it on website. ...
Hi, I am merging the multilink example and the CDC ACM example in SDK15.
However, if you merge and run it, it will continue to fail.
Here is the source.
I have...
Hi, i am using a model based on simple_on_off model to send custom messages.
For now provisioner and client are separated as in the V2.0.1. I tried to combine them first...
Hi,
Is it OK to use the Nordic Semiconductor ASA (0x0059) ID for broadcasting data in the manufacturer specific data field?
If so is does Nordic provide a specification...
Hello
For the BLE Mesh 2.0.1 demo i bought some nrf52840 develboards. Then i write the demo with "python scripts/quick_start/quick_start_demo.py" to the nrf52840 develboard...
Dear Nordic Team, Thanks for supporting.
I want to know the possible for mesh network concept with nRF52832 (PCA10040). If possible means guide me for startup.
Regards...
HI!
I'm a happy owner of two nRF52840 Preview DK board (v0.9.3). I'm considering to change their chips to production versions. I found that schematics and PCB layouts are...
Hi,
We are using nRF52832 for one of our central device. Our peripheral is also based on nRF52. We are facing issues while scanning for the peripheral from the central side...
