Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
I'm working on a custom board with an nRF52382 connected to an IMU over I2C. The IMU provides 2 separate interrupt signals, and I would like to route each of them to a separate...
Hello,
Today I've a strange behavior of nRF51 DK (everything was working ok until today, the last things I did was to reset the J-link FW after a total erase of the board...
Hi all,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using an "app_timer" in repeated mode with 10Hz frequency...
I have recently acquired a NAND chip from Micron and would like to use it for storage.
However, looking through the datasheet I found out that the addressing scheme require...
I'm planning using nRF52810 for a new product to reduce the power consumption.
But i worried whether old smartphone with Bluetooth4.0, like Iphone5s can connect with equipment...
I am dealing with the nRF24L01 to develop a remote controller. When I read the specification, I found a specification item, called C/ICO, with a typical value of 12dB in the...
hello,
I'm trying to send long (73B) data on a given characteristic using Android client as the central.
I well received:
USER_MEM_REQUEST OK
> #define...
Hi to everyone!
I'm following this guide to learn how to use secure DFU on a nRF52832DK board.
All steps have been done successfully, or I think so, until I reach the...
I want to find the agent of China, please, thanks
About Bluetooth and 2.4G, nRF52840/nRF52832/nRF52810
(The agent can provide some technical support and sales)
Can someone please explain the below line mentioned in NRF5 Serial port abstraction layer documentation.
Do not use synchronous API (timeout_ms
parameter > 0) in IRQ...
Hi there,
I want to flash nrf51 firmware from another MCU which is connected to nrf51 with UART interface.
I have seen dual bank serial bootloader examples, in that firmware...
Hi,
I know this has been touched on in other posts but I can't find a definitive answer.
I am making a product that sends data from a handheld joystick to a base station...
Hi All!
we are trying to tune Antenna use DTM over UART from examples.
It is works fine for AAAA IC but doesnot for AABB IC.
Why, what's possible problem?
thx...
Hi everyone,
My configuration:
nrf52832 microcontroller
Softdevice S132 V4.0.2
Nordic SDK 13.0
I need to develop a repetitive task with 10 Hz frequency...