Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Is the nRF Temp App source code available for download?
I am currently developing an ultra-low non-connectable beacon and would like to use the nRF app as a starting point...
I guess all the Bluetooth members saw the email from the SIG about the next version of Bluetooth and how it is confirmed to have double the range, quadruple the speed and...
I'm looking at table 23.15.2 in the nRF5 Reference Manual, and it states that TX startup current is 4mA with the DC-DC enabled.
Does that 4mA include the CPU idling...
My project: nRF51422, S110, based on SDK 7.1.
My project employs several application timers (run via the scheduler) and a continuously running Timer1-based 1ms timestamp...
Hello again,
i wanna use the UART communication for transfering data from my µc to the nrf51 and vice versa.
For a test i used the ble_app_uart example and it works...
Hi,
I programmed my NRF51 to read ADC samples and I trying to transmit the information to a dongle. So far I have been able to send the hexadecimal values of the recorded...
Heyho!
Is it possible to set the PWM base clock frequency to 40kHz? If so, how? I see that the predefined base clock frequencies don't go any lower than 125kHz.
I'm...
Hello everyone, I am program for PCA10001 and I want to use Bootloader to upgrade firmware through OTA for my device. I have a old file bootloader use for s110, and I tried...
Hey,
I would like to send data from Central to Peripheral. I follow by ble_app_uart example, however I need to send a float type variable, so I split it to the total and...
I have 2 identical nrf52832 development boards with PCA10040 V1.1.0. One is running the ble_ant_app_hrm example from the nRF5_SDK_11.0.0_89a8197. This example appears to run...
Hello,
I'm developing a product using nRF51822 which is intended to work with iPhones (only iPhones for now; iPod/iPad and Android later).
I need some kind of document...
Hello,
I'm trying to recreate the PWM_library example from the v.11 SDK in a new file in Keil. I have compared the debug settings in my project to the debug settings to...
Hi there,
I am following the thread to use JlinkExe and JlinkRTTClient. I encountered a situation which i don't understand.
After running JlinkExe (go to the folder...