In my project, I have configured a USB Mass Storage (MSC) device that uses a QSPI flash, like the one on the 52840DK board.
My system goes into sleep mode when a button...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Using latest SDK and toolchain 3.0.1, VSCode and nRF Connection Pack on Windows 11 I nearly never see a working nRF Kconfig GUI - only the first time directly after I had...
I noticed that in the hid_mouse sample, the whitelist advertising was used to achieve seamless recovery of accidentally disconnected connections.
This function is implemented...
Hi everyone, I'm a beginner in Nordic development and currently learning how to work with BLE and Zephyr (NCS 2.9).
I'm using an nRF52840 Dongle as a peripheral and an nRF5340...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hi,
I have a reset issue when trying to set a delay greater or equal to 100 milliseconds using nrf_delay_ms(...). This only happens if I start my app timers (app_timer_start...
Hi,
I am trying to generate a 128Hz sine wave using the nrf_pwm library . First I tried this with SD110 enabled but ran into some problems that turned out to be a known...
Hi,
I'm going through the errata and a few of them look serious that the developer kit might be useless for some of us if we want to use it for any realistic testing (I...
I am trying to add a static passkey to my peripheral and protect from MITM. I tried the example nRF51-ble-app-uart-static-passkey but it doesn't seem to work correctly.
...
Hi,
I am new to nordic n51822, i have implemented adc and timer independently.
Now, what i want to do is read the adc values on a specific time when the timer overflows...
Received my nRF52 preview board yesterday and have been battling to get my S130 based nRF51 code running on it with the S132 soft device (the code is here: github.com/......
The codes i am using is
nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral and nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_peripheral\ble_app_hrs
From the peripheral...
Just getting started with the PCA10001. I can compile if I select the device nrf51822_xxaa_s110, but when I load it tells me "can't load flash device description".
It subsequently...
I have take the basic ble_app_hrs_with_timeslot and modified it to calculate the timing of subsequent calls to the timeslot START event.
Specifically,
take note...
Hello,
I'm trying to get the new SDK up and running on my OSX machine. I would like to make the blinky example work on my PCA10003. So, I copied the blinky/pca10028 folder...
Hello, Do you guys know if it is possible to generate a stable 38kHz signal using the Nordic?
I have been able to generate the required frequency however I am observing...
Not a question but thought worth mentioning.
developer.nordicsemi.com/.../
Good News
PWM library changes seems to have made it into the release.
Bad news:
Looks...
Hello,
I am working on an nRF51822 custom board application which is reading data from external sensor through TWI. It is based on the MPU6050 driver available in the SDK...
Hi there,
Before I asked this question, I have searched similar question about TWI example, but it seems there were some guys looking for such example as well. Not sure...
