I am using the following version of nrfjprog on my Windows 10 machine:
nrfjprog version: 10.24.2 external JLinkARM.dll version: 8.44a
Most of the sub-commands work with...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hi,
I am developing an acoustic platform with my custom board with a nRF5340 CLAA chip. The board is recording audio data from two microphones at a sampling rate of 100...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
Hi, We have used nPM1300 on our development board around nRF54H20, but we are experiencing an strange issue. - when power is attached VBUSINILIM0/VBUSINILIMSTARTUP value is...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
hi,there
raspberry can ping6 pca10028, rasberry can receive udp packets from pca10028.
but how can i ping6 pca10028 from pc?
env: pca10028 + csr ble dongle + raspberry...
i'm confused of the relationship of wirepas and ant+,both claim to surpport mesh network and multihop.what's more confusing is that both are promoted by nordic.
I look up...
I find in the following example code that if I start my application from a powered-off to a powered-on condition and main() executes the code as shown, everything works fine...
Hi,
I do receive undefined HCI errors in my disconnection handler. I wait for the BLE_GAP_EVT_DISCONNECTED event and use the bleEvent->evt.gap_evt.params.disconnected.reason...
I've been reading through the documentation for pstorage but there's one term I don't understand
devzone.nordicsemi.com/.../a00131.html
What is the purpose of offset...
We are using two GPIOTE inputs and there is only 1 GPIOTE interrupt handler.
One of the GPIOTE input is from a power line chip that toggles @ 50 Hz rate. This GPIOTE input...
Hi Team,
I was trying dfu to load my application.
Edit #1
I have flashed softdevice.
Then I have compiled the example project 'dfu_dual_bank_ble_s110_pca10028...
I have an external temperature on my nRF51 DK. I would like to read the value of the temperature on my mobile device(Android).
I am able to read the temperature on the...
I would like to use the single shot timer and when the timeout handler is called, I would like to set up the same timer again with different interval this time. Do I have...
There seems to be a discrepancy between the 8.0.0 softdevice release notes and the product compatibility matrix. I would like to know if it is possible to use 8.0.0 softdevice...
Hi,
In my project, I need to periodically perform some jobs on the nRF51822 Beacon kit (sdk 7.1). For that, I think I need to use timers. However, I'm not sure how to do...
Hey everyone.,
I was trying to use nrf51822 as spi slave and just a heads up to know that i use Nrf51822 as master. I see that when chip select CS gets low SPI needs to acquire...
I've added a custom service and a few characteristics on the nRF51822. How can I access the current value stored in one of those characteristic outside of a BLE event occurring...
Hi,
I'm unable to run any application on nrf51 DK (Keil used). When I start debug (no matter what application I load), program always cycles between 2 instructions:
0x000006CC...
Hi,
My application uses the softdevice 110.
Everytime, there is an event on my sensor. The sensor sends the event to my pin, which generates a gpiote interrupt . But, the...
