I am using the nRF52840 dev kit, I have setup nrf connect sdk v3.4.0 and v3.4.0 toolchain, signed up with ANT and added ANT to my west yaml file. The first issue I had was...
we run long-term HIL tests with typically 3–8 nRF9151 DKs:
DKs spaced only about 1–3 cm apart
short USB 3.x cables to powered USB 3.2 hubs directly below them
sometimes...
Hi
Our project uses the nRF52833 SoC without an external PA. During the Korea KC spurious emission certification, the out-of-band emission on the first channel in DTM 2...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
1.What is the maximum rate that the QSPI of nRF54L15 can achieve? 2. Is it possible for me to use QSPI to read the flash memory while simultaneously refreshing the screen...
Hi,
I want to ask if the Nrf54l05 supports application image compression. I asked Nordic AI and they said it’s not supported, but I want to know the reason why it’s not...
Can anyone verify what two pins are used for NFC on a FANSTEL - BM20C module? I've been in contact with Fanstel for over a week, but they haven't given me a definitive answer...
In our application, we need to save a group of data objects,
how many data objects in a group is dynamic.
also each data object has different sizes,
a few bytes up to 100...
Hi,
I am using nrf51822 custom board.
I'm trying to make intterrupt when a pin is 0 (or 1) and do some calculations while it remains 0.
However I could not manage...
Hello,
I am trying to use SPI on a mbed nRF51822 and am following the documentation suggestion. We've deleted all code except the minimum to try and track down the problem...
Hi,
i want to build an applicaiton with gcc and eclipse setup and S130. I use OSX.
if i don't use the softdevice and run it with the blank linkerscript my blinky code...
Hello,
We are trying to update to Keil uvision 5.11 and unfortunately breaking our teeth on the pack Installer. The Nordic SDK 5.2.0 is installed on the machine but when...
Hi,
I have installed nRF Master Control Panel app on custom board running Android kitkat 4.4.2(ASOP).
But when I run MCP app it gives prompt that 'Device doesn't support...
Hi all,
I develop a central application, which manages multiple peripheral connections. The application often has to stop and start scanning again. In rare cases the function...
Hi,
I'm trying to get the bootloader from SDK v6 running with SoftDevice v7.
I managed to compile it under Eclipse (gcc). I've just removed buttons and LEDs from the code...
I would like someone from Nordic to confirm that the new softdevice release s110_nrf51822_7.0.0 is not suitable for the 128kb versions of the chip (in my case nRF51822 QFABB0...
Hi!
How is the functionality choosen, the nRF51822 has to offer?
Is the SoftDevice (e.g. SD120) an API in C where a specific functionality (e.g. central role listening to...
Is it possible to use nRF51822 Development Kit without nRFgo Starter Kit? What I need - is to be able to connect couple of LEDs and buttons, can this be achieved without buying...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...
Hi,
After doing an sd_nvic_SystemReset(), the bootloader does start advertising, but for some reason the android app nRF Master Control cannot connect to it.
If I connect...
