We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
I have two nRF9151 DKs and want to evaluate direct, SIM-free DECT NR+ communication using FT and PT roles. Please help me with:
- DECT NR+ MAC/PHY modem firmware, rather...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The action was executed, and the date and time are...
Hello. Using the Zigbee messaging cluster, we are writing code for data exchange between ZR and ZED. (Based on the Zigbee example light_bulb/light_switch/light_coordinator...
Hello,
I have a custom board which has an nrf5340 on it. We are using nRF Connect/Zephyr in this project. Currently the board has a pretty simple interface seen in my overlay...
I am currently developing a PC application for Bluetooth data reception and chart display. I want to perform secondary development on pc-nrfconnect-ble. My current development...
I'm using SDK15.3 on an nRF52840 with FreeRTOS and specifically non-preemptive scheduling.
I want to so some transfers on SPIM (it's configure with DMA but that's not a...
My project uses a PDM microphone connected to a nrf5340. I previousy had this working using the nrfx_pdm driver, with NCS 2.6 but then had to migrate the project to NCS 2...
There is usually a panel for application where you can see / delete or add build configurations, as shown in the enclosed picture. The panel on my vs code installation has...
Hello,
i am debugging issue in our device. I ported the nrf5340 Audio application to our custom board and modified it for our use. We use audio broadcast mode.
Device...
HI,
I am developing a ble mesh application on SDK 17.2, I enable Instaburst for support long mesh message(more than 300 byte), it worked well.
Now I changed to the nRF...
Dear Support Team,
I'm trying to develop a mouse using Pixart's PAW3395 sensor. I've written functions for reading and writing data through the SPI interface. I took help...
I didnt see in the data sheet a specific window of time the chip needs to properly shutdown without interrupting a critical process that might cause corrupted memory. I am...
Dear Nordic Engineers
I would like to test the GPS of NRF9160 with CMW500.
I used a line(IPEX to SME) to connect the GPS pedestal to CMW500.
I downloaded the serial...
Hello,
I am currently working through the nRF Connect SDK Intermediate training in preparation for an upcoming project. Said project will require communication between two...
Hello. I'm trying to run a sample with sending data via Lora. I'm using llcc68 but as I read in previous threads, the code for sx1262 should work on my chip.
Here is my...
