I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Im trying to get SAADC to continuously sample using internal timer but im getting couple of samples and then it stops, tried everything but I'm obviously forgetting something...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
Hello,
I have a Insight ISP4520 SIp which include a nRF52832 chip and a SX1261 for Lora radio https://www.insightsip.com/products/combo-smart-modules/isp4520 The internal...
I'm using
the nRF52840 DK and the Matter light_bulb example, SDK v2.7.0.
a raspberry pi with the nRF dongle as a thread border router
the chip-tool running and compiled...
Al over these example programs there are all these messages like
LOG_INF ( "Filters matched. Address: %s connectable: %d " ,
addr , connectable );
How do you actually...
Hi,
We are using nrf52840 with nrfSDK-16.0. We have implemented extended advertisement in BLE 5 LE CODED PHY. We want to try periodic advertisements. Do we have any examples...
My custom device uses nRF9151 and we're using SDK 2.6.0 with modem firmware 2.0.1.
When the device connects to the LTE network it derives a default APN, however, my provider...
Hi,
I’m exploring the use of the Thread/Matter protocol for a smart lighting system. My goal is to have the system communicate seamlessly with the cloud—allowing commands...
I am using a LattePanda 3 Delta running an Ubuntu server OS (x86) headlessly. I am using a RS-232 cable to obtain the modem trace from my custom board, which uses an nRF9160...
Hi,
We are currently starting a project using the nRF52832 as our controller, Segger Embedded Studio 5.42a as our IDE, and nRF5 SDK version 17.0.2.
Project Requirement...
I have found a bug in SDK v2.6.0 at zephyr/drivers/flash/nrf_qspi_nor.c while erasing the external MX25R64 flash.
Environment:
nRF5340 DK Hardware (MX25R64 external...
Hi
We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
HW: nRF5340DK NCS: v2.8.0
After installing NCS v2.8.0 from ToolchainManager, I tried to build the project but failed.Error message "No such file or directory: LIBGCC_FILE_NAME...
I have a Raspberry Pi Pico which is powered by a Lipo battery. I want to measure the current with the Power Profiler Kit II. I hooked the 2 grounds to to the board, and VIN...
I am using BLE mesh in nrf52840. I have modified the sensor server sample and sensor client sample to suit my requirements. I am using toolchain and sdk v2.6.1. It is working...
