**Setup**
- Custom board, **nRF54LM20A** , first bring-up. The SoC is powered from an
nPM1300: BUCK1 = 1.8 V feeds VDD.
- External **J-Link** (firmware compiled Jun...
Dear Nordic team
we have customer would like to know if nRF93 support voice ， like voLTE or simple using Application-layer voice solution over the LTE data channel?
they...
nrf54l05, SDK NCS3.0.0, using MCUboot, with external PY25Q16HB as new firmware staging area. During upgrade, attempting to observe CLK waveform, a test wire was soldered onto...
Hello,
We are seeing a west build reproducibility issue on nRF Connect SDK v3.4.0 that we have narrowed down, through extensive elimination, to the compiler's code generation...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151-LACAA1A design, and I would like to make sure I understand the recommended correction for...
Hi,
I'm using the Thingy:91 X PCA20065 rev 2.0.0 as a reference for a new nRF9151 design, and I have three related questions about BUCK1 and the 1.8 V rail.
1. nRF5340...
Hi, I am a beginner into the embedded audio space, and happened upon this board to use for our university project. Our team's current plan would be to produce audio directly...
The network stack from Zephyr is not working correctly on my nrf5340. I want to receive data from a custom driver through the network stack to my application. For this, I...
As noted in other discussions, like the one I've linked below, there is no timing information for the QSPI interface. Can Nordic please provide the timing information for...
Hi! I'm able to update the firmware on the nrf5340 over BLE but the BLE settings seem to get overwritten during the update. The master device cannot automatically reconnect...
Hi, im working in a project with the nRF5340-QKAA and I need VDD as output 1.8V, for this reasoin I supply the uC with 3.6V on VDDH like this image:
this works fine...
I'm working on developing a desktop app, which can communicate with nrf52840-dongle or any Nordic device. I'm using UWP to develop the app. I'm new to App development so i...
Hi,
I'm evaluating the nRF9160-DK with the SOFTSIM feature enabled.
I would like to know if there is a way to tell the softsim to wait for APDU response for more than...
Hi, I have a BLE application where I want to use the device firmware updates (DFU) over Bluetooth. I followed the nRF Connect SDK Intermediate tutorial on how to enable the...
Hello!
I'm using the nRF5340 for a school design project and as such am financially limited to relatively low cost board manufacturers.
It seems that most of these manufacturers...
Greetings,
I'm trying to add an existing folder from a project with its' contents, but it seems that it only adds files that are included in the folders, the other nested...
Hello,
I am currently working with the Nordic nRF9160DK and am using the https_client example from the examples in the nRF Connect via VS Code (on Windows OS), and as far...
Hi,
I have been trying for months now and don't seem to find a way to build a signed app for mcuboot without having to build the whole mcuboot itself.
In the board files...
hi,
I am using nrf9160+NCS v2.6.1. When the CONFIG_SHELL_BACKEND_RTT feature is enabled, the power consumption increases by 80uA. After investigation, I found that the default...
Hi
Built and flashed ncs2.7.0 SLM application at NRF9151 DK. It will log booting log messages and then "Ready" as below.
Before ncs2.7.0, I found SLM application only...
