I've trying to get MCUBOOT woth work with my project & after much time/effort & found my project, untoughed, works on the nrf52840DK. I then discovered that the mcuboot build...
Hi! We have recently upgraded nRF Connect SDK. Since this change, some of our users experience issues with uart - two nRF52840 communicating together. We have not been able...
Hello,
I am working on a project based on the Nordic nRF54L15 microcontroller, using nRF Connect SDK and Zephyr RTOS. The application handles BLE communication in both advertising...
Hi all,
Quick question on NFC design practice.
I am using the nRF54L15 NFC in tag emulator mode (differential), with the following setup:
Antenna: Molex 1462360051...
Hi
We have a fleet of nRF9160-based sensors in the field (mfw 1.3.x, NCS 2.7.0) with ab Azure IOT Hub Connection over MQTT / TLS.
For FOTA we are using azurewebsites.net...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hi,
I am debugging a case where an nRF9160 cannot register on LTE-M in New Zealand using a multi-IMSI SIM(korewireless). The modem establishes an RRC connection, then stops...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi everyone! I'm having difficulties in setting up a little project in which I want to pass I2S data over USB. I know I'm using the old USB Audio Class endpoints, but everything...
Hi,
Initially, I can send and receive AT commands. But after sending the power-down commands
sequence from "Getting Started with nRF93M1 DK v0.4"
I could not receive...
I've trying to get MCUBOOT woth work with my project & after much time/effort & found my project, untoughed, works on the nrf52840DK. I then discovered that the mcuboot build...
Hello,
Thank you for your help.my questions are as follows
SDK : ncs 3.4.0
Hardware board ：nRF54L15
Based on the ncs SDK 3.4.0, how should one set the MAC address...
Hi! We have recently upgraded nRF Connect SDK. Since this change, some of our users experience issues with uart - two nRF52840 communicating together. We have not been able...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Hello,
I am working on a project based on the Nordic nRF54L15 microcontroller, using nRF Connect SDK and Zephyr RTOS. The application handles BLE communication in both advertising...
Environment : - nRF Connect SDK v3.4.0. - CONFIG_SPI_NRFX_SPIM_RTIO=y. - SPI_HOLD_ON_CS is not enabled. The same completion ordering is present in upstream Zephyr main : https...
Hello,
We run a small fleet of battery-powered nRF9151 devices (Thingy:91 X) on modem firmware mfw_nrf91x1_2.0.4 and nRF Connect SDK v3.1.1. The modem regularly asserts...
