First time here? Check out the Tour!
The Arduino SDK by David Edwin linked to here is no longer available since the Bluetooth forum seems to be down, and has been for some time: https://devzone.nordicsemi.com/arduino
Is there an alternative download source for these files?
Hi, I have been using the nRF8001 Arduino SDK with nRF8001 chip. I wanted to set the data for the different services I'm using and thought I would go ahead and use the services.c file generated by nRFGO ... (more)
Can anyone tell me how to connect NRF 8001 with Arduino mega 2560. I have developed an iPhone application and just want to connect with NRF 8001.Please tell me how to connect NRF 8001 with Arduino mega 2560 and ... (more)
I'm using the redbearlab shield in combination with an arduino uno r3. I want to send sensor data at about 10 hz to my smartphone.
This works but sometimes I get an error 0x91 (Pipe Error Event : Credit ... (more)
Hi! I'm using Arduino BLE micro and good results so far. With some accellerometers connected via I2C.
Today I have a strage behaviour. I connect the arduino, ok, open the ble receiver on the Mac OS/X, ok, receiving ... (more)
I tried changing the broadcast name which was not easy but after installing the nRFgoStudio and editing the XML file with it - I managed to change the name yet the UART program no longer works . I verified this issue comparing ... (more)
If I've missed some documentation on the use of Nordic Semiconductor's nRF8001/nRF24L01+ Adapter for Arduino, I apologize but I couldn't find any.
Steps I've taken:
I have an arduino connected to a redbear BLE shield. the BLE shield uses nordic nRF8001 chip.
How could I implement RSC ? (running speed and cadence) I would like to test it with the nordic app for ios and android ... (more)
SoftwareSerial library allows GPIO pins to be used as TTL serial pins by bit banging.
The nRF5 suffers from the same problem that the Arduinos have. 1 UART.
Does the nRF5 have a similar library to make up for this deficiency?
I use RedBearLabs Nano (nRF51822) for at setup where I've developed BLE code in Arduino to communicate with apps on both iOS and Android.
Now I need to ensure the communication with encryption.
I've read these ... (more)
Hi, I'd like to connect my nRF2740 to my MCU Arduino Micro and test it with the sample codes found in your GIT repo. How can I do this? Best regards, Alessandro
I want to set up an SPI communication between nRF51422 SOC (integrated on nRF51 DK) and Arduino board. I know that it is possible since I've read it in various posts and nRF51 reference manual. But, I couldn't ... (more)
I am playing around with the BLE_proximity_template on the Redbearlab BLE shield and an Arduino Uno. I uploaded the sketch and paired my Android Lollipop device with the shield. Success! The serial monitor now encourages me to "Do more ... (more)
Hi, I'm planning to add bluetooth LE support to my Arduino based project. I want to use nrf52832, but I couldn't find any example on Arduino interaction with this radio. I know that nrf8001 has an SDK for ... (more)
Using the nrf52 DK, I was trying for hours to setup Segger IDE on a mac, and the software doesn't feel good to me, its not clear where is your code, it has too many libraries, it feels cumbersome ... (more)
Hi, i have a strange issue on connecting nRF24L01+ module to Arduino pro mini. I use arduino pro mini, nrf24L01+ module, 3.7V 6000mah battery and DS181 chip to measure temperature of any room wirelessly. I write a sample code ... (more)
We're building a low cost device with an nRF8001 as the only means of communication as physical access is closed after the device is built.
Is there any way to change the nRF8001 output mode to stream data directly ... (more)
Hi, I'm looking to build a simple ANT+ application. My only asset for this project is a background in C/C++. I'll need to learn/relearn the basic electronics and protocol bits. I had thought to use an ... (more)
I have a few nRF51 dongles I wish to use with ANT+ for wireless mesh communication between some robots. I want to connect each to one ATmega 1284p and another Arduino Mega with ATmega 2560, both 5v chips. Can I ... (more)
Arduino start selling Arduino 101, powered by an Intel Curie processor.
As far as I have seen here, Intel Curie module integrates nRF51822.
I was wondering how we could use deeply the Intel Curie, behind the arduino part, implementing ... (more)
I am trying to integrate BLE into my wireless heart rate monitor project with an Arduino Uno.
Everything works and can successfully be exported over a different BT antenna to a custom android app. Now I have purchased the nRF8001 ... (more)
I couldnt get nrf8001 sdk for arduino from bluetooth.org,is there any other way to get it?
I am really confused at the moment if the Arduino SDK is for NRF8001 or does it also works for NRF51822? Can you please help me in getting started?
Thanks Hani Abidi
Hello I'm trying to utilise the multiceiver mode with nRF24L01 and Arduino, the idea is that an nRF will be able to send a message and six other receivers will be able to receive it. If there's such ... (more)
Hi, i have only little experience in programming a nRF51, but i want to make just a simple application. before i used a btm222 BT2.1 SPP module to transmit serial UART-data via Bluetooth - that was pretty easy. now i ... (more)
Hi guys, I have to port the current library that is working at the arduino uno for arduino zero pro but when I change the board type I get the following errors:
__file__.ino:39:69: note: in expansion of ...
Hi Friends, I like Nordic and Arduino, it's great if Nordic can support Arduino officially, we can use the ARM0 in Nrf51822 as a single control point of Arduino project. There are some projects created by other community to ... (more)
I want to connect Arduino shield with heart-rate sensor to my nRF 51 DK board. then i have to receive sensor data continually from the sensor.
my plan is transferring this data from my DK to my raspberry pi ... (more)
I cannot find any instructions on how to "pair" the nRF8001 with a laptop (I understand that BLE doesn't pair like usual BT).
Are there any tutorials available?!
Hi everyone on the community.
I've been struggling trying to upload the hex file created by arduino using redbear nrf arduino fork on a NRF51822 -v2 board that is being sold at ebay.
the hex file size is around ... (more)