Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
(NCS 2.5.0) Unable to OTA if the device is previously bonded. 0

Hi, We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
14 views

0 replies

Started 2 hours ago
by PuffinEgg
Not Answered
Failing to receive UDP packets with zperf in OpenThread network 0

Hi all, I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
- software
- 802.15.4
- Evaluation
- zephyr
- nRF5340
- openthread
13 views

0 replies

Started 4 hours ago
by aghuang
Not Answered
Combining CS Reflector and Periodic Sensor Broadcast on a Single Advertising Set (ME54BS01 / nRF54L15) 0

I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
34 views

0 replies

Started 7 hours ago
by Thanos Vasiloglou
Not Answered
nPM1300 Battery Status Voltage value 0

Dear DevZone support, I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question. I understand that I can...
20 views

0 replies

Started 11 hours ago
by pipoket
Not Answered
ABOUT ZIGBEE OF NRF54L15 0

Hi Nordic： We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
- development
- software
- zigbee
- nRF54L15
21 views

0 replies

Started 12 hours ago
by jermi

Recent in Nordic blog

nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018
Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018
The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018