Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Is the nrf54L10 output spectrum stable above recommended vdd 0

Hi, Is there a way to implement overvoltage lockout by sensing VDD using the ADC? Our goal is to claim that we have power regulation so that we can get full modular certification...
11 views

0 replies

Started 49 minutes ago
by RFEE
Not Answered
Title: nRF54LM20 DK debug-out (P13) reset line holds an external nRF52840 target in reset after a pin reset or CTRL-AP hard reset 0

Setup - Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
13 views

0 replies

Started 1 hour ago
by dm1
Not Answered
LED doesn't blink on nRF54L10 custom board connected to nRF54L15-DK 0

I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09. #include <zephyr/kernel.h> #include <hal/nrf_gpio.h> ...
25 views

0 replies

Started 2 hours ago
by Star0
Not Answered
nRF93M1-DK – No data connectivity over USB RNDIS/CDC-ECM 0

I'm trying to establish a data connection from a Linux host through the USB network interface of an nRF93M1-DK. The modem registers successfully on the cellular network...
33 views

0 replies

Started 3 hours ago
by packetmoose
Not Answered
Memory Access Error when erasing/writing external flash and HW WDG enabled. 0

We are currently working with a system that is using both and external flash and the HW WDG from the NRF5340. Recently we are facing the issue, that we cannot re-flash the...
19 views

0 replies

Started 3 hours ago
by Jaro

Recent in the DevZone Blog

Nordic's infocenter

Oisin

The Infocenter – our new documentation portal - has now been up and running since June and contains all of our technical documentation. We saw the need for this because we wanted to make our complete…
- 24 Aug 2015
nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015