Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
WIFI SoftAP + Station mode in one compiled image 0

nRF54LM20 + nRF7002, NCS 3.4.1: SoftAP provisioning and station low power in one image Our battery-powered product (no BLE antenna), removed due to space in the PCB and...
70 views

0 replies

Started 2 days ago
by SubuMuthu
Not Answered
Energy consumption in NTN mode vs LTE-M 0

Hi Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M? In particular I am curious if NTN has...
58 views

0 replies

Started 2 days ago
by ovrebekk
Not Answered
Can’t generate ncs-sbom with nRF Connect SDK v3.1.1 0

Hello. When I ran the NCS SBOM command using VS Code, the following error occurred, and the file could not be generated. I would appreciate it if you could tell me how...
61 views

0 replies

Started 2 days ago
by Fumiya
Not Answered
Title: nRF54LM20 DK debug-out (P13) reset line holds an external nRF52840 target in reset after a pin reset or CTRL-AP hard reset 0

Setup - Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
69 views

0 replies

Started 3 days ago
by dm1
Not Answered
LED doesn't blink on nRF54L10 custom board connected to nRF54L15-DK 0

I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09. #include <zephyr/kernel.h> #include <hal/nrf_gpio.h> ...
69 views

0 replies

Started 3 days ago
by Star0

Recent in the DevZone Blog

Writing BLE firmware with a few lines of code part 2

Nguyen Hoan Hoang

Second part of the series Writing Bluetooth LE firmware the easy way blog. This second part shows how to read and advertise the environment sensor data (BME280 using Motsai Neblina module and BME680 using…
- 3 Jan 2018
Intro to ShockBurst/Enhanced ShockBurst

Daniel Veilleux

The first generation of wireless PC accessories to achieve widespread success (the ones that shipped with a dongle in the box) adopted 2.4GHz radios because these radios offered the optimal trade-off between…
- 1 Jan 2018
Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017