Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to send/Tx IMU sensor Data/Values 0

Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
- nrf24l01+ arduino nano mpu6050
1882 views

0 replies

Started over 9 years ago
by Franks
Not Answered
Using NodeJS libraries on Linux to talk to Nordic BLE devices 0

I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack. ...
- bluetooth low energy
1207 views

0 replies

Started over 9 years ago
by helpme
Not Answered
S110 8.0.0 and RIOT 0

Hi, I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
- s110
- riot
- nrf51822
831 views

0 replies

Started over 9 years ago
by pixiedust
Not Answered
iBeacon usage as pairing less UART extender 0

Hello everyone, I got a task which I try to implement using a NRF51822 iBeacon board. The Task: Advertise a Device and provide a mechanism to connect without traditional...
944 views

0 replies

Started over 10 years ago
by pk
Not Answered
MPU6000 SPI 0

Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
- nrf42522
- mpu6000 accelerometer spi
1334 views

0 replies

Started over 10 years ago
by Josue

Recent in Nordic blog

A presentation on how nRF51 DFU works

Hung Bui

Hi, I attached here some slides that we used in our technical seminar for Device Firmware Update. Download the presentation here: DFU_SDKv8.0_Pub.pdf The presentation covers: What DFU is and what…
- 4 Jun 2015
Parse MQTT message in Wireshark for IoT test

Jun Qing ZOU

Wireshark (version 1.12.5 at the time of writting) lists MQTT as supported protocol but could not parse it from the TCP payload by default. We can add some plugins to enable it. Download the Wireshark…
- 26 May 2015
Upgrade RADVD for IoT on Raspberry Pi 2

Jun Qing ZOU

The RADVD deamon in Raspberry pool is version 1.8.5 (up to Raspberry 2015-02-16). root@raspberrypi:~/radvd# apt-cache policy radvd radvd: Installed: 1:1.8.5-1 Candidate: 1:1.8.5-1 Version table…
- 25 May 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019