Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
atomic fifo implementation on armv7a 0

Hi Nordic Team, The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
- development
- software
- nrf5 sdk
- arm
563 views

0 replies

Started over 4 years ago
by misaka
Not Answered
Regarding ble mesh data transfer 0

Hi, Kit:nrf5340 Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts. Is ble controller will be enabled during...
525 views

0 replies

Started over 4 years ago
by Priyadharshini
Not Answered
Modem firmware python script file or dependency missing 0

I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
566 views

0 replies

Started over 4 years ago
by okwestern
Not Answered
Connecting nRF52840 DK to MC3672 Accelerometer and nRF52840 Dongle to Mac 0

Hi, I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
- development
- nrf52840 dongle
- SDK Documentation
- nrf52840 dk
- bluetooth 5
- nrf5 sdk
- spi
- bluetooth le
- nrf52840
- usb
- hardware
718 views

0 replies

Started over 4 years ago
by Jaz
Not Answered
HID Remote and Central . 0

Hi I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 . USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
537 views

0 replies

Started over 4 years ago
by meghna

Recent in Nordic blog

Nordic's infocenter

Oisin

The Infocenter – our new documentation portal - has now been up and running since June and contains all of our technical documentation. We saw the need for this because we wanted to make our complete…
- 24 Aug 2015
nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019