Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Which mode can use to set up a dynamic network?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

611 views

0 replies

Started over 10 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

795 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1304 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn
View Voters Login to vote on this thread 0 Login to vote on this thread
0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1257 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
885 views

0 replies

Started over 10 years ago
by Pedro Lopes

Recent in Nordic blog

On nRF Connect for the Mac, the new nRF Edge Impulse and the Discovery of SwiftUI

Dinesh Harjani

Preface The bulk of the development work described in this blog post occurred during the 2021 calendar year. This means it reflects the state of iOS, Mac, Swift, and SwiftUI Development before and after…
- 1 Sep 2022
Traveling the embedded world 2022

Finn Boetius

The embedded world trade fair presents itself as the leading trade fair for embedded systems. It allows the embedded community to get information about new products and innovations. But also allows us…
- 3 Aug 2022
Developing and testing Bluetooth Low Energy products on nRF52840 in Renode and Zephyr

Michael Gielda

The Bluetooth Low Energy (LE) connectivity standard has gained immense popularity in recent years, mainly due to the growing ubiquity of IoT solutions in both consumer electronics and industry. Thanks…
- 4 Jul 2022

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022

Nordic DevZone

Which mode can use to set up a dynamic network? View Voters Login to vote on this thread 0 Login to vote on this thread 0

nRF24AP2 Rx behaviour View Voters Login to vote on this thread 0 Login to vote on this thread 0

Logging UART data on a PC View Voters Login to vote on this thread 0 Login to vote on this thread 0

Which priority does softdevice set for SWI2_IRQn View Voters Login to vote on this thread 0 Login to vote on this thread 0

What is the way to have a simple BLE chip work? View Voters Login to vote on this thread 0 Login to vote on this thread 0

Which mode can use to set up a dynamic network?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

nRF24AP2 Rx behaviour
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Logging UART data on a PC
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Which priority does softdevice set for SWI2_IRQn
View Voters Login to vote on this thread 0 Login to vote on this thread
0

What is the way to have a simple BLE chip work?
View Voters Login to vote on this thread 0 Login to vote on this thread
0