Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
ncs 2.8.0 fails to build zephyr's bluetooth ISO_CENTRAL and ISO_PERIPHERAL samples on 52840DK 0

HW: 52840DK PCA10056 3.0.1 2023.16 NCS SDK: v2.8.0 I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
39 views

0 replies

Started 10 hours ago
by banco
Not Answered
When connecting to AWS IoT with low signal it gets stuck 0

We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
27 views

0 replies

Started 14 hours ago
by charleshaf
Not Answered
the file: thingy53_nrf5340_cpuapp.conf in v2.6.0/bootloader/mcuboot/boot/zephyr/boards 0

Hi Community, I made a custom board based on thingy53, created a similar custom board file folder. The application code can be compiled correctly with the original thingy53...
30 views

0 replies

Started 1 day ago
by danny0007
Not Answered
ADC channels are not providing the proper values when integrated 0

I am making a device using the nrf52dk that takes data from 5 separate sensors and sends the data to a nrf52840 dongle. My trouble lies with the ADC data collection. When...
36 views

0 replies

Started 1 day ago
by dmangoldusf
Not Answered
NRF8240 HCI UART support setting public address 0

Does the NRF8240 using the HCI UART sample support setting a public address? https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/bluetooth/hci_uart/README...
49 views

0 replies

Started 2 days ago
by samanthacho

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022