Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

CE—compliant nRF24LU1+ module 0

Hi Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine. There are many modules...

494 views

0 replies

Started over 9 years ago
by Salvador Sancha
Not Answered
scanf was not working on radio_test application with sdk v10 on PCA10001 board. 0

I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7. I am using mincicom on linux at baudrate of 38400...
- nrf51422 s120 sdk 7
638 views

0 replies

Started over 9 years ago
by Siva Subrahmanyam
Not Answered
nrf_uart example and Windows Phone 10/Windows Phone 8.1 0

Hello! I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028). I am using SDK 9.0 with S110 softdevice ver. 8.0.0. I was using examples...
- nrf51822 windows8.1
551 views

0 replies

Started over 9 years ago
by michal_grzes
Not Answered

Cann't run the BLE code 0

Hi I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...

753 views

0 replies

Started over 9 years ago
by Alice
Not Answered
detect button toggle with PORT event 0

Hi, I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo. To my understanding PORT events are generated by...
- port
- nrf51822
- button
1329 views

0 replies

Started over 9 years ago
by gammarui

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019