Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
[NCS 2.6.1] NFC T4T response timing 0

Hi, I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
0 views

0 replies

Started a few seconds ago
by kartapusse
Not Answered
NUVOTON + NRF24L01 Software Development. (SPI Communication) 0

Hello Everyone, I try to develop Nuvoton + NRF24L01 SPI communicate each other. And I don't understand why MISO bus has 0x0E after I send Write_Command 0x20? void NRF24_AdressTX...
- nrf24
- development
- software
- 2.4 ghz
- Other
33 views

0 replies

Started 35 minutes ago
by electric eye
Not Answered
Does the battery profile file (created by fuel gauge board) run on other PMIC? 0

Hi Sir, As check below link, the battery profile can support on non-Nordic MCU. (+) Does the PMIC nPM1300 support Fuel Gauge feature for MCUs outside the nRF SoC family...
19 views

0 replies

Started 57 minutes ago
by Hsu
Not Answered
Pin switch control pin when sharing multiple drivers 0

Hello In my board I am using an ic as a switch to control the routing of the TX and RX pins of the UART, due to the fact that the nRF9160 does not have more than 4 peripherals...
16 views

0 replies

Started 1 hour ago
by Avgerinos89
Not Answered
No SOURCES given to Zephyr library 0

I am building firmware using nrf connect sdk v2.8.0 and I am seeing those warning on the build Here is the prj.conf
23 views

0 replies

Started 1 hour ago
by MOHAMED AHMED ALI MAHMOUD ELSABAGH

Recent in Nordic blog

nRF Connect v1.0 Release Candidate

Hung Bui

Note: This post is outdated. Please go to the product page for nRF Connect for Desktop for updated information and downloads. nRF Connect is the new official name of the Bluetooth Smart tool previously…
- 9 May 2016
How to test nRF52 NFC tag with reader (Adafruit Tag Reader)

Brian Kim

Since NFC is one of new feature on nRF52, some customers often ask how to verify NFC tag they are implementing. The purpose of this blog is to provide how to setup and how the implementation based on SDK…
- 9 May 2016
A modern approach to Bluetooth LE and the Internet of Things

eric ely

Bluetooth LE is ideal for Internet of Things applications where many low powered sensors or devices feed data through a gateway and out onto the internet. An optimal solution would move away from the use…
- 6 May 2016

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022