hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi ,
We are using NRF52, S132 softdevice ... Whenever we do hard reset everything works fine .. But if I do flash from my IDE (using eclipse,this is a soft reset) and it...
I have a hard time to initial a twi ,I reference the example in the SDK11.0，and I used the board is 10040,I copy the example twi sensor code in my project ,but there is an...
I'm getting the error code 0x4001 from sd_clock_hfclk_request and I can't find where the error codes are defined/explained for this function. Can someone point me in the right...
Hi,
With the following program running, how can I achieve the lowest power consumption between timer events:
nRF Timer is running with the HF crystal requested
...
51822, config a pin as output , in the param , set disconnect or connect the input pin, when config as output ,what mean disconnct/connect input pin?
I use a pin to light...
For my project to simulate the spreading of a disease I am thinking of recording the complete social network on the beacons and then collecting the data to a pc. I have roughly...
I am using nRF51-DK hardware and working on the ble_uart_app s130 SDK_11
Upon power-up, nRF51 is discoverable and connectable. After sometime, it is no longer discoverable...
Hi, I am using microESB library. We want to test the continuous carrier wave mode for ESB(similar to using DTM for BLE continuous carrier wave mode). Is there any library...
Hi,
I have the nrf52 working perfectly in iBeacon mode. Even when my iPhone is Off, the iPhone will wake up and post a notification with UUID, Major,Minor etc.. It's great...
I have suspended my Beacon in SLEEP (at .5 uA) until a keypress. Is there an event that can trigger an event if there is a low voltage detection while in SLEEP?
My goal...
hello,
I am trying to write one characteristics on GATT server from a client. My server program (acts as peripheral) is working fine with MCP. But when i am trying to connect...
Hi,
I've spent the last few days trying to get this going and getting super frustrated.
After having no luck getting the nrfutil to work on Python ( another thread ...
HI,
I am using micro esb(0db tx power, 250kbps, RX mode) from GitHub( github.com/.../nrf51-micro-esb) . I am using nrf51822xxaa and SD10.0 and s130. With just the micro esb...
I can't get the Master Control Panel to work. I think the drivers might be messed up but various re-installs aren't having any success.
Can you suggest some troubleshooting...
