Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
I need help with this issue. I'm updating the code from SDK 2.4.2 to SDK 2.9.2. I had change the device tree to HWM2 and I'm using sysbuild.
The build log is showing this...
I am currently working on a 3D game in Unity (made in C#) and I am asked to connect a Nordic Thingy:52 nRF6936 (based on the nRF52832 SoC) to Unity to control a part of the...
Hi,
I'm developing custom firmware on the appcore and netcore. The netcore runs BLE controller, as well another custom IPC service to communicate between the appcore and...
The OSCILLATORS documentation says:
" The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
Hello,
I was given an existing code with a possible bug in it relating to RAM retention and I'm trying to make sense of what I'm seeing. I am using NRF52832 with SDK 17...
Function: Now we have developed a function similar to usb file upgrade on the application side by ourselves (which requires operating bank1, writing the Settings page, involving...
Hi,
we are looking into incorporating a NRF52 module into our control units, but to allow extending the antenna position away from the case through male-female SMA cables...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi There
while extending the actual Sofware with more flash entries i discovered that the capability of provisioing devices decreases, and end up in a hardfault.
Is there...
Hello
In my board I am using an ic as a switch to control the routing of the TX and RX pins of the UART, due to the fact that the nRF9160 does not have more than 4 peripherals...
Hello, I am developing a project that involves authentication over NFC, and need to store a private key in TrustZone. I found the psa_crypto zephyr sample in the sdk, which...
Hi everyone,
I’m trying to understand how wireless mice/keyboards using 2.4 GHz protocols communicate with their receiver dongles so that i can try build one using nRF...
Hi,
I wanted to implement a version of Channel Sounding where you wait for a certain amount of distance estimations, and then try to just select the smallest distance...
Hi, I'm encountering an issue with one particular nRF52832 unit (we use nRF SDK 15.2.0). The problem is that a value 0x20 (decimal 32) is being written to a memory address...
I've been working off this example, which provides a great synchronization mechanism.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/conn_time_sync...
