Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Im having problems running DFU serial examples.
i use one of the examples of the SDK but it seems like board doesnt leave the bootloader mode and memory value doesnt change...
Does someone could tell me where can I find information on the sequencing of events BLE_EVT_TX_COMPLETE and packet transmissions during connection periods?
In my application...
Hi,
I am using nrf51822 evaluation kit, and the sample program i am working on is ble_app_hrs.
I have created 4 characteristics with notify property and also created...
Hi every one,
I'm working on a custom broad and I'm trying to setup a gazell based protocol.
I had a solution using soft device and BLE which worked fine but we want to...
Hello,
I'm a few novice in BLE, and I've got a problem.
I'm using a custom project based in UART example. I'm using Nexus 5 and nRF ToolsBox for text it. I'm saving...
Hi! I want to send the temperature data that I get from the beacon sensor not one by one but in packets for example of 100 samples. I have followed this tutorial devzone.nordicsemi...
Hello,
I am trying to get SPIS EasyDMA to work. Currently the SPIS MISO response with high when the CS is pulled low by another master device, but no correct data present...
I'm trying to add more buttons to the nRF51 DK.
But I get an error.
I have found the NUMBER_OF_GPIO_TE define.
#define NUMBER_OF_GPIO_TE 4
How can I handle more...
Hi, is there RSA-512 cryptography (or maybe another asymmetric cryptography system) implementation for nrf51 or some implementation that can be easily ported to nrf51?
Hi. I played around with the MQTT example on nrf51822 module.
I get it connected to an openwrt device and can connect/publish to mosquitto on button press.
In next step...
Hello all
If you could please point me some directions on how to solve my issue, I would be grateful:
Some background info:
SDK used: 9.0
spi master code =...
Dear Nordic Developer Zone,
I have a silly question. After searching in the Nordic and Bluetooth documentation, I didn't find what CCCD and SCCD mean. Theses metadata are...
I had a design on 4-layer PCB with nrf51822, then the requirement was changed, then the 2-layer is sufficient for routing.
But I thought 4-layer PCB is better for RF circuit...
I've run into a problem with an OS API call when running FreeRTOS on an NRF51 due to how ticks are corrected.
vTaskStepTick() is getting called while the MCU is awake and...
Hello all,
I am trying to activate ADC to measure a voltage every few seconds using nrf51822. When it is done, I supposedly deactivate ADC so it does not consumes while...
