I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I wrote a program that uses ESB communication between two nodes. On both sides I use the same ESB configuration and the same ESB init function, the difference is only...
Hello,
Environment: nRF51DK + SDK8
We've developed the beacon application but the advertising interval is set to 5 seconds. The beacon can be discovered by nRF Connect...
I have searched here on the DevZone, and also around the web, and don't see this issue mentioned elsewhere. I really appreciate any help finding a solution.
I tried following...
Hi All,
I think I noticed a bug in the nRF Connect v1.0 application. The Scan Response data is not shown in the Windows application. When I scan the device with the iPhone...
nRF8001_BLE_UART.txt
I am using an NRF8001 with the ble_uart_project_with_dfu_template and programmed an ATMEGA328P with it. The code works great and I can scan and communicate...
Dear sir,
Can we use 8.08.90 J-LINK EDU for programming of Nrf52832 Chipset.Please also specify its limitation if it has any.
If we cannot use this then please specify...
I'm starting to use Wireshark a little more and sometimes it is not displaying all of a device's manufacturer data. For example on some devices it is not displaying the manufacturer...
hi,
As a ambitious tech lover i bought BLE400 nrf51822 motherboard. I downloaded SDK 11.0, keil and nrfgo. I started programming based on the Nordic developer Zone. I first...
Hi, I try to connect nrf51822 and use example "ble_app_hids_mouse". I can pair this device and I confirmed that "Notify" becomes automatic at that time in Enable.
But, when...
Hello,
I am working with the Enhanced ShockBurst protocoll on a nRF52832.
For synchronization reasons between several nodes I need time stamps in my data packet...
hi, i build a test project to test IAP(in system program) function of nrf24le1. the project just did follow things:
1. setup uart;
2. erase page 30
3. write data "0xaa...
I'm new to nrf8001
I'm trying to understand an existing example.
in this example after sending set up commands generated by nrfgo studio , program sends 9 byte of 0xff command...
I downloaded central and peripheral ble UART and I want to add some function to my code and use some GPIO, I programmed nrf51822 by nrf51422 source code and it worked, but...
