Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
HI
sd_ble_gap_adv_start() is returning INVALID_PARAM when it's being calling in ble_advertising.c I have read through the documentation and I don't see anything incorrect...
Hello all,
I try to send a command to read device ID (0x9F) of a micron memory device (N25Q064A) using SPI protocol. I have the following hardware configuration :
NRF_SPI_CLK...
How does the Tx power impact the scanning and connection with a peripheral?
In detail, say if the peripheral can advertise at a Tx power of 4, 0 or -4 dB, then will it...
Hello, dear Nordic employee,
MCU: 51822QFACA1
The using SDK is : SDK 7.2.0
The using SD is : s110_nrf51822_7.3.0_softdevice
There was one device (our product) runing...
Hi,
I am using "nrf5 sdk v11.0" example "ble_ancs_c" for nrf52_DK(PCA10040) .
when i connect to the nrf_device from ios device i am able to pair and connect to ancs client...
Hi,
I'm using the example nRF5_SDK_11/examples/ble_peripheral/ble_app_uart witn a pc10028 board. The central is done on a linux machine with a python program under bluepy...
Hi,
We would like to use the nRF52 in the following way:
BLE communication via S132
button / IRQ to wakeup nRF52 application
put nRF52 to sleep after BLE communication...
As we known,RSSI means Received Signal Strength Indicator,TXPOWER decide the power of output port.How do the two factors combine affect the device work?
Hi I spent a few days on trying to setup a thread external commissioner using Nordic nRF52840 and RaspPi 3 as a border router.
First I realized that border router implementation...
Hi
I'm having major problems implementing current time service client (cts_c). I've run ble_app_cts_c on my device and it works fine. I copied the relevant parts of the...
Bluetooth SIG recently released BLE Mesh standard 1.0. Is nordic mesh compatible with the new released SIG standard?
If not when is it planning to release a SIG compatible...
Hello,
I did used nrf_drv_spis.c (SDK SPI Slave) with nrf_drv_spi.c (SDK SPI Master). And I notice that both module configure SPI MISO line as input without any pull (neither...
Hello,
I am using nrf52832 DK and I would like to use the GPIOs port to debug a couple of signals that I genereate within the MCU.
So far I have configured my GPIOTE...
Dear experts,
I've been playing around with Thread since nRF5 SDK for Thread v0.8.0, cloud_coap_client.
I use your Border Router example with NCP example running on nRF52840_Preview_DevKit...
Hi:
I got an 0x04 no mem error with sd_ble_enable.
But my hardware worked just fine before, so after some tussle I found out that the sd_ble_enable of my working program...
