This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
I did a chip-erase on the NRF51 DK. However, when I tried to reconnect and program the DK I get the error: Failed to connect to target, no Idcode detected
I tried doing...
Hello,
At the following line
I get the error:
hal.c(35): error: #20: identifier "NRF_DRV_TWI_INSTANCE_0" is undefined
When looking further it seems likein the...
I have custom board with nrf 52832. I am using SDK 15.2.0 and softdevice s132 V6.1.0 to transmit advertising packets periodically. I have written simple application that reads...
Hi Everyone,
I’ve implemented a ST7735S on the NRF52832 using the GFX example. My problem is that I can’t seem to update the screen in such a way that the screen doesn’t...
Hello,
I am trying to make LSM6DSR (STEVAL-MKI194V1) work with nRF52840 using TWI Communication.
Problem:
Firstly, I modified the TWI sensor example to use the accelerometer...
Hi guys, I've got a nRF 52840-DK, I want to verify the new features like 2M/long range/advertising extension.
1. Is there any exmaple to test these featues, or any guideline...
Hello,
On the nRF52840, is it possible to switch from TXIDLE to RXIDLE or from RXIDLE to TXIDLE without going first back to DISABLED ?
We are using the radio in 1 Mbps...
To the kind attention of Nordic support team,
we are very much interested in interacting with your nRF52840 devices preprogrammed with the wireless bootloader and waiting...
Hi! We are currently trying to develop a low power framework for our nRF52840 DK with SoftDevice S140. After disabling various peripherals and interrupts we use the provided...
Hello Team,
I just recently purchased Thingy52 i was wondering i can use NFC NDEF update using python library if it is possible can you point me to right
documentation...
Hello!
I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption...
Hi,
We are currently testing DFU upgrades on Android. In my current setup I have two different phones, a Sony one running Android 8 and a OnePlus running Android 10.
The...
We have a device (in central mode) initiating a secure connection to a peripheral (slave) via the usage of `pm_conn_secure(conn_handle, false)`. This results in a `PM_EVT_CONN_SEC_SUCCEEDED...
Hi All,
I want to convert analog input into digital using SAADC on nRF52840 DK. After that to push the SAADC output through the Bluetooth (nRF connect bluetooth mobile application...
Hi,
Recently,i try to install the tool chain of nrf connect sdk as the instruction as guide。After installed west,then run command “west update”,but got an error:
Can...