Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I am using SDK15.3.0 and softdevice 6.1.1 on a nrf52DK.
I have a binary (compiled contiki application) that works when I flash it using nRF Connect. It is flashed from address...
Hi,
I have a PCA10040 board (nRF52-DK) which has a P20 debug out interface. I've got another nRF52832 breakout board which has VCC/SWIO/SWCLK/GND wires for debug/programming...
Hey,
I configured one device as low power node in mesh network.
With the button press interrupt low power node wakes up and perform some operation (publish BLE message...
Dear Nordic
I am using SDK14.2, I cannot pint info . SDK periphral uart and serial can't print also
nus example jlinkrtt print as below:
<00> warning> nrf_sdh_ble: RAM...
Hi,
I am using pc-ble-driver version 4.1.1 with the SD version 6.1.1.
I want to configure the TX power for the NRF52 USB dongle.
Do you have a code example for configuring...
Now I can build & download nRF52840 SDK example with Eclipse.
But Eclipse indexer(F3 key) can not recognize include folder.
So I added every include folder to .cproject...
I'm having a advertising device and then I want to stop advertising and prevent BLE connection from device that would have received the advertisement. It seems to work by...
Dear Team,
I am trying to add my Thingy 91 to nRF cloud, but I receive the following error :"There was an error adding your device: No device found with id 'nrf-xxxxx'....
Hi Nordics
https://devzone.nordicsemi.com/f/nordic-q-a/22595/can-not-received-ble_gap_evt_timeout-event-when-connect-timeout/88877#88877
Referring to the above post, I...
Dear,
I am trying to test BLE on the THINGY:91.
Follow the Q&A for "Introduction to Nordic THINGY:91" webinar, Q12 of @ Petter Myhre
I tried with Zephyr HCI UART example...
Hi,
I'm trying to debug my bootloader (I2C specifically) using Ozone. However the CPU only seems to halt when trying to debug the bootloader.
Also setting breakpoints...
I am using proprietary radio between 2 nrf51 devices, by copying from an example see code below.
That works but now I want to have more pairs of devices and I need to have...
Hello,
I have some custom hardware that uses both BLE 4.0 and BLE 5. I am looking for information on if it is possible to use a nRF52840 Dongle to connect to multiple peripheral...
Hi ! I am trying to design a custom board for nRF52840. I used the nRF52840 dongle's HW files in Altium to create a new board. Unfortunately the Altium project does not include...
I am trying to make the timer example works under the BLE blinky example. I have copy the code and enable the defines in sdk_config,from one project to the other but timer...
