I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hello
I am using nrf52840 from nrf9160dk, I am trying to run example from nrf52840 with sdk16.0.0 and sd7.0.0. While checking data on uart I am getting following error...
Hi
I'm trying to get a DFU boot loader working on our own custom hardware. My initial approach was to build secure_bootloader_ble using my own public_key.c file and try...
I updated my Thingy:91 today to version thingy91_fw_2020-04-29_bc7ade8b.
I flashed the mfwnrf9160120, the thingy91_nrf52_connectivity_bridge_2020-04-29_bc7ade8b and the...
Hi, I'm developing firmware for the trf7970a nfc chip. For standard communication the chip uses spi, but a special direct mode uses an additional two wire interface where...
Do the values for current consumption given for the scenarios in Section 5.2.1 of the nRF52833 PS include the current for any peripherals required? E.g. the PS quotes 2.6uA...
Hi!
I am trying to merge the basic/button sample with the mqtt-simple sample.
I added to the prj.conf of mqtt-simple sample.
My main.c looks like this:
After merging...
Hello!
Iam trying to get the spi function to work properly on my thingy 52 device.
My problem is that the transfer wont stop when it should in my opinion, i have analyzed...
Situation: SES, SDK 16, nRF52832
I'm developing a pre-production test program without BLE. I'm using APP_TIMER_V2 and noticed that the timer events do not not happen even...
We have a custom board with nrf9160, ncs 1.2.0 and modem fw 1.1.1. We experience strange behaviour with the GPS: As an example,on units with 30 min fix intervals, we experience...
I added the commissioning part from the nfc_meshcop example to the mqttsn_sleepy_subscriber example. I tested the nfc_meshcop exaple and worked, so the border router part...
Hi,
I have developed a project of mine based on the nRF52840 DK and now I want to place
the nRF52840 chip on my custom 2 layer PCB board but I think that it might be very...
We still have some Problems to use the Supl client Library, to test it we use the normal GPS example and seems like the connection is available with NB-Iot settings. We are...
I have a product which uses the nRF52840 SoC that will also have NFC functionality. The housing of the PCB is sort of forcing a custom design for the NFC Antenna.
We need...
Hi All,
I am using Segger ISP1430603E board to program my nRF development kit. ( ISP1507AX )
With SES I am able program, debug the application.
I would like to program...
