I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi,
I was wondering if you could give me information on the validity period of the GPS assistance data?
In other words, how often do you need to download the data...
Hello,
I am working developing an application that sends data as notification to connected host at the data rate of 2KB/sec. The chip being used is NRF52832 with S132 soft...
Hello there; My setup: NRF52832 SDK 15.3 I'm facing some problems with FDS when i use it with BLE activated.
When i read or write on FDS using fds_record_open or fds_record_update...
I followed the steps mentioned in the Bluetooth low energy Characteristics, a beginner's tutorial, but at "if ((p_evt_write->handle == p_our_service->characteristic1_value_write_handler...
Hi, I tested "Simple_coap_client" and "simple_coap_server" on NRF52840 using Threading SDK.
I want to change the transmit power, so I used "otPlatRadioSetTransmitPower ...
52810, LIS3DH, I call nrf_drv_twi_tx got NRF_ERROR_DRV_TWI_ERR_ANACK return using either TWI/ or TWIM . Here is my code:
const nrf_drv_twi_config_t config = { .scl = TWI_MASTER_CONFIG_CLOCK_PIN_NUMBER...
Hello,
I want to verify with you if the Standby current for My Bluetooth 5.0 corresponds to the system "on" according to the Bluetooth datasheet or there is another way...
Hello, we've built up quite a bit of experience programming Nordic targets with Keil and nRFgo studio. We love your products. However, we are considering moving away from...
I'm trying to get debug output to appear in my Segger J-LINK SWO viewer (from an NR52840 SDK board with NRF5 v16) which I understand is a potentially complicated process;...
I use Peer Manager for storing bonding infomation with nRF52832 (SDK14.2) using gcc.
I understand Peer Manager uses FDS, and FDS uses flash memory from 0x7D000 to 0x80000...
Hi All,
I know this question seems to have been asked many times already but still does not seem to work for us even after checking forum answers.
Hardware: Fanstel BT832...
I have followed up this example and compiled successfully but the NFC pairing is not working at all.
I use my smartphone (Google Pixel 2) to touch the NFC antenna and nothing...
I can control GPIO P0,but can't control P1, when I load project with nrf5340_dk_nrf5340_cpuapp ns configuration.
If I load project with nrf5340_dk_nrf5340_cpuapp configuration...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am running a custom application which uses the...
