Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
SDK: nRF Connect SDK v2.9.0
Chipset: nRF52840
I'm using ncsv2.9.0nrfsamplesperipheralradio_test to test the RF.
The initialization code is as follows:
At this...
Hello,
We are using the nRF9151-DK board and have soldered a new eSIM chip onto it. However, the eSIM is not being detected by the Cellular Monitor, even though we have...
I've buld bluetooth mesh/chat for NRF52840 dongle and it worked a long time ago. But today when I create a new sample mesh chat, it can't build and here is the log err in...
Hello,
I am working on a project using the nRF Connect SDK, and I need to implement both BLE HID and USB HID. I would like to know:
Is it possible to use BLE HID and...
I have a requirement where I'm using a .NET-based test adapter that communicates using the Modbus protocol over a serial (COM) port.
Now, I want to develop a BLE Central...
Dear all,
i configure pin 3 to float input.when the pin3 input 0.3VDD--0.7VDD,the chip current have 25--400ua,other is normal(4ua) Why?
SDK:8.1.0
s110
#define PHOTO_PIN_NUMBER...
Hi,
I am using nrf pwm library from here: github.com/.../nrf51-pwm-library . I am driving two gpios for a piezo buzzer.
I call pwm_init(), then use the call set_frequency_and_duty_cycle...
Hi,
I am trying to run a MIDI slave chip with the nRF51822 which requires me to use the MIDI standard baud rate of 31250. Is it possible to use nrf_drv_uart with a custom...
Hi all,
i use the function sd_power_system_off() to put the micro in system off.
First question is about the the type of system off. There are different type of system OFF...
Hi Forum and Nordic Employess
I use sdk12.2
The Pstorage libraries are missing. I want a Pstorage (flash write / read) example along with the Soft Device.
Thank You
Hi all,
I see there are similar questions posted on this forum, but none answers my question satisfactorily.
What I have:
we use the nRF52 we use UART0 to
transmit...
I'm using SAADC on a NRF52832 DK to read a analog channel between 0-3.3V. I wanted to supply current with the board VDD but it's value is 2.8V and they're not event stable...
Hi
I'm trying to get higher throughput when connected as a central by increasing my Tx&Rx bandwidth to high (from the default medium).
uint32_t nrfErr; ble_opt_t opt...
Hello,
my custom board does not have external 32kHz crystal. I have managed to use NRF_CLOCK_LF_SRC_RC in SOFTDEVICE_HANDLER_INIT instead.
My questions are:
...
I have a Custom Board made by using nrf51822 soc but pc is unable to detect the board by using Jlink debugger.
Stlink was able to detect only when frequency selected as 20khz...
Hello dear Nordic Team,
I got a question regarding the device filtering options. I am interested in putting 10 chips next to each other. But every chip shall have only...
As I came to understand, all the services & characteristics are registered in a "GATT table" of some sort, so my question:
What are the functions used to create and...
I want to update the nordic device from another MCU with HCI DFU. I cannot figure out how to write the packet header.
In the Nordic documentation, it is writen to read the...
I want to add micro-ecc library for compiling bootloader secure code.
I tried as mentioned on infocenter.nordicsemi.com/index.jsp .
I am getting error as attached. I am...