Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi
I am planning to use the nRF52833 for the AoA direction finding application. On that I had two questions.
1. Currently I have two nRF52833 DKs for transmission and...
Hi all,
I am developing on nRF Mesh SDK 4.0.0 with nRF52833 DK (PCA10100).
To save/restore persistent model state to flash, I added the code using mesh_config_entry_get...
Hello,
I'm new with the nordic chips and SDK and have a short question: I'm trying to send the battery capacity of my BLE device within the advertising data. I found some...
Hi
Do you have any example code to support OCF standard and/or IoTivity (Lite).
Or any plan to support IoTivity?
(We're targeting OCF supported device with nRF52832...
Hello all,
I am running "ble_app_beacon" example code in nrf52832. when i'm using samsung and honor mobile phones the nrf Connect application is not showing the beacon,...
I'm trying to enable the CMSIS Wizard on SES 4.42a. I followed the instructions and pasted the required xml into tools.xml, saved the file and restarted SES.
This is my...
Hi Support,
I need to use another eSIM not the iBasis, because the company those not have roaming coverage in Bulgaria.
Question: If I use a IoT eSIM card Telefonica...
I want to send a one byte payload from the nrf24l01+ (Sparkfun dev board), to nrf52840 DK using the example esb_prx. How should I configure the nrf24 registers to make this...
We have run the Hello World program on the nRF5340-PDK, but now following the basic steps to program the heart rate example, there is no BT broadcast for Zephyr Heartrate...
Hello everyone. I'm creating a setup function to configure LSM9DS1 accelerometer and gyroscope by writing to the corresponding registers as shown below
Although this code...
I use sdk16.0 and nrf52832.
Can you give me an example of nrf52832 timeslot example ? thank you.
I read timeslot on DevZone,but many routines are missing files, resulting...
Writing an app for the Arduino Nano 33 BLE Sense:
https://store.arduino.cc/usa/nano-33-ble-sense
Basically I am reading all sensors on the Sense board (temperature, humidity...
I have programmed a Nordic Thingy 91 with lte_ble_gateway, and when I send command from the cloud to the device, an NRF_CLOUD_EVT_RX_DATA event is called, however evt->param...
