Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi everyone,
I have an nRF52840 DK. So far, I have been programming the nRF DK using the UBS connector J2 and everything worked great.
Since yesterday, by following the...
I want to update status in manufacturer specific data of advertisement packet. is there necessary to stop advertising first then reinitialize advertisement data and again...
Hello peeps,
nRF52480 I2C Interface with Invensense ICM 20948. I am using SDK 15.2. I see there is some Support for MPU 6050 Invensense but not for ICM 20948. A lot of Registers...
Hello,
I am currently working on the nRF SDK for Mesh v3.1 and I am using a static provisioner as in the light switch example. I have merged the client and server functionality...
Hello! I have a custom board with a NRF52832 chip that is working fine with the last program I flashed into. But since yesterday I can’t access it to load a new code (flash...
What all do I need to modify in the Blinky peripheral (from SDK 16) with in order for the 840 DK to advertise and connect with CODED PHY in long range mode?
My code compiles...
Hi everyone,
I am looking at using MQTT v3.1.1 with TLS 1.2, to send data to Azure IoT Hub.
I tested the MQTT Simple sample and it worked perfeclty. So I am modifying...
nrf52832 , I have flashed ble_peripheral/ble_app_uart with simple modifications
ble doesn’t advertise while Jlink/seggar debugger is connected to our custom board.
...
I use SDK16.0
use BLE + Multiple Beacon, Beacon use timeslot,BLE use softdevice.
I want to modify the advertising content of BLE,But use advertising_stop->advertising_init...
I'm currently working on integrating modem FOTA updates into my application. I have the FOTA working at the moment, I'm able to go to and from a FOTA-TEST version with the...
I try to run this sample https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/mqtt_simple from the master branch, but when I connect to the network...
I'm connecting the battery to the VDDH 3.6V or 3.7V and sensor to VDD, it means nrf52833 get powred on from VDDH and sensor get the power from VDD. is it ok? please check...
I use the nRF52840 MCU and SDK 16 with S140 softdevice. I want to use spi interface to control 3 SPI slave. They share the same SCK, MISO and MOSI. I use 3 chip select pis...
