Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi all,
I've got a single Thingy:52 (FW v2.1.0), and no DK. I'm trying to upgrade its firmware through nRF Connect on Android, but keep on running into a FW version failure...
Hi to everyone!
I have a custom board (based on nRF52832) with two LEDS and other GPIO ports. In some point of the code I have to activate one device by setting one port...
Hi Guys,
Will they work at the same time?
i want to use the MCU for UART and at the same time i want to run the BLE GAP events parallely.
is this possible? and how...
Hi all,
I have two pwm pins I would like to have them run at two different duty cycles. My understanding is that we can do this by setting the decoder to individual. When...
Hi, We are facing issue related to pc_ble_driver shared library at the time of run script.
Traceback (most recent call last):
File "SDFTest.py", line 414, in
init...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
i'm developing an application with the NRF51822 device using the NRF51 development kit (DK). I bought a power profiler kit (PPK) to measure current for advertising...
I am using nrf52832.
I am setting MIN and MAX Connection Interval both to 7.5 ms as android support 7.5 ms connection interval. We are getting 2-3 packet in one connection...
We are in the process of upgrading from from soft device v 2 (with SDK v 11) to soft device v 5 (with SDK v 14), and we have a portion of our code that controls connection...
Hi averyone,
We are developing the BLE project whith two devices master/slave.
The master device is built on the NRF52832 processor with SDK14.1 and it's program is built...
nRF52832 is in a sleep state.
However, when the Watchdog timer clear processing is placed in a different position, current consumption changes.
If the Watchdog timer...
Just wanted to ask: is this expected that nrfGo Studio doesn't work with the micro:bit?
Presumably this means that nrfGo Studio doesn't work with CMSIS-DAP in general?...
Hi,
We're using nRF52840 rev. A with s140_nrf52840_6.0.0-6.alpha SoftDevice and patched SDK 14.2.0. We've succesfully launched Long Range advertisements on one device and...
