Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...
Hello,
I am working on the project through the BLE Multi-link Example.
In the description of the BLE Multi-link Example, "The central device can have a maximum of 8 concurrent...
Hi Nordic team
I have a question about Litepoint bluetooth advanced nRF5x OTA Testing.
According to the White Paper v1.0, by using the heart rate app, it is easy to evaluate...
Hi,
I am using the ble_app_uart_c example for the ble_central of SDK 12.2.0 to send data over UART to a nrf52832 based peripheral. When following the format as suggested...
i use sdk14.2 52832 as central , have bas service and myself service it have pair process , there are one change question. When I first burned the program, the bas service...
Hi,
I'm using Noble.js on a central RPi3 for DFU updates over BLE. The process is several times slower than doing the DFU over nRF Connect on an Android phone. I believe...
I am designing a NRF52 based device. One of the component , Crystal X1, EPSON FA-128 32.0000MF10Z-AJ3 used in the reference design is not available for purchase in online...
On the included Thing52 example, the LED fires m_ioext_osc_status_change from an interrupt. Eventually, when it comes to requesting use of the TWI this comparison happens...
I've noticed that if I call app_usbd_cdc_acm_write with the length set to any multiple of 64 the data will not show up on my PC until I do another write with a value that...
Hi DevZone,
I am modifying an CAN library for nRF52840 preview DK. In my project, nRF52 preview DK is working as a SPI master and Arduino CAN Bus Shield is working as a...
