I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
I'd like to use new nrfx drivers included in SDK 15. The problem is that I want to use C++ but nrfx header files are for C. The struct initializers can't be compiled as C...
I have a lot of pin_read function. How can i set all port one line? for example P1OUT = (P1.01 | P1.02 | P1.03) or P1IN = ( P1.01 | P1.02 | P1.03 ) I dont know how to use...
I created a simple message mode based on the simple_on_off modle,when I debuged the codes in simple message client,I got an error(app_error),I never changed the codes for...
hello,
I used NRF52832 as a ble gatway.Now i have a trouble that the received signal strength is jumping about 2dBm when the chip loaded program.I test it with Spectrum Analyzer...
Hello! I am trying to prototype a DFU solution that works well for our application. We want to build a network with both normal Mesh devices and with friend nodes (once that...
Hi,
for my PCB, i'm using an NRF52832 as SPI slave, i send an array of 4 bytes {0xA5,0x00,0x01,ff}, but my SPI master receives always a byte (0xff) before 0xA5.
this...
Hello everyone
I have kind of a basic question.
I'm not sure how to manually disconnect from a ble connection. I'm using the ble_app_uart and ble_app_uart_c examples from...
Hey all,
We’re trying to figure out the best way of keeping our nRF52 (or 51) based design in the lowest power mode possible while sitting in inventory.
Currently, our...
Greetings,
I have 12 sensors each of which is located on an nRF52832 board. I need to collect the sensor data at 50Hz (10 bytes for each sensor).
For some reason I can...
This one is throwing me for a loop.
We just did a small build of 40 devices based around the nRF52832. 1 device out of those 40 is behaving very strangely. When the device...
Hi Sir
I want change the power transmission level for measuring the RSSI values for different configuration from -40DB to 4DB. for that i configure the radio. But it is...
When compiling (after the project folder change and paths updating) I get always this error.
No idea why. The C99 option is choose
It compiles correctly from SDK tree...
Hello,
I just finished migrating my project from SDK13.1 to 15.0. It caught my attention that when I flash the Softdevice, it uses memory from pages 0x00000 - 0x24000. I...
I think I found a bug in nrf_ringbuf_cpy_get. The first memcpy is wrong. The source and destination should be swapped.
if (length > trail) { memcpy(&p_ringbuf->p_buffer...
Hello,
I am using the NRF51822 in a low power application and need to transfer the data from the PCB (with the NRF) to the PC over Bluetooth. I need the biggest possible...
